Sanyo CE42LH2DPB, CE42LH2WP instruction manual Mains Connection, Connections

GB INSTALLATION GB

Step: 1 Mains Connection

N&RQQHFWWKHGLVSOD\XQLWWR9*$%1&DQG6FDUWFRQ-

nector as required. LD-Net

7KLVÀJXUHLVLQFKPRGHO

1.Connect the in-line power connector to the Mains Inlet as shown above.

2.Connect the power cord of the LCD monitor to a suitable wall outlet.

As this product does not have a mains On/Off switch, please ensure your mains plug is easily accessible.

The LCD monitor is prepared for a mains voltage AC100 ~ 240V,

+]+]7RFRPSOHWHO\VZLWFKRIIWKHPDLQVRUZKHQWKH GLVSOD\XQLWLVQRWWREHXVHGIRUDQH[WHQGHGSHULRGRIWLPHLWLV advisable to disconnect the power cord from the power outlet.

Please use the correct mains lead supplied with the set for your area.

3.Warning: To prevent injury, the unit must be securely attached to the wall in accordance with the installation instructions.

WARNING! High voltages are used in the

RSHUDWLRQRIWKLVVHW5HIHUVHUYLFHWRTXDOLÀHG

service personnel.

Step: 2 Connections

NNINPUT selection

To switch either AV1, RGB, AV2, AV3, PC, DVI or Network by pressing the INPUT button on your remote control repeatedly.

1.AV1

SCART connection/CVBS/RGB/S-VIDEO.

2.RGB

TTL input (5V RGB signals) into SCART terminal.

<3E3U5*%+9FRQQHFWLRQ$9

4.AV3

Composite (CVBS) signal input.

AV3-OUT can be used to output the incoming AV3 signal to the other monitor.

5.DVI-D (Digital Video Interface)

DVI-D supports a large range of resolutions as shown in the IN- STRUCTION MANUAL on page 17.

6.PC connection

PC input (PC-IN D-SUB). This input supports a large range of reso- lutions as shown in the INSTRUCTION MANUAL page 17. Audio can be connected via the 3.5mm PC-AUDIO IN.

7.External Speaker

Output the audio signal from AV1, AV2, AV3, PC and DVI. The speaker impedance is 8 ohms.

8.AV2 / DVI AUDIO IN

Connect the audio output (stereo) from a computer or video equip- ment connected AV2 or DVI.

9.Monitor Audio OUT

7KLVWHUPLQDOVRXWSXWÀ[HGOHYHOIURP$8',2,1

English

Choose Y, Pb, Pr or RGB H/V connection by selecting AV2 Setting	10. RS232C IN/OUT
in Set up menu (refer to the INSTRUCTION MANUAL on page 10).	When the monitor is controlled by a computer, connect to this jack
You can connect your DVD player to the Y, Pb, Pr terminals instead	with serial control cable.
RIXVLQJDVFDUWOHDG7KLVFDQVXSSRUWKLJKGHÀQLWLRQLQDQDORJXH	You can connect to another monitor with RS232C OUT.
component form. RGB H/V can be used as a PC input via the BNC	:KHQ\RXFRQQHFW3&ZLWK56&VHOHFW´21µDW1HWZRUN
terminals. Both options support a large range of resolutions (refer	standby in Installation mode.
to the INSTRUCTION MANUAL on page 17). AV2-OUT can be used	,ILWLVVHOHFWHG´2))µ56&WHUPLQDOVGRQRWIXQFWLRQDO$OVR
to output the incoming AV2 signal to the other monitor.	VHOHFWSXVKEXWWRQWR´6(5,$/32$57µ

11