Sanyo DVW-7200 Setup Connections, RF Output Channel, Hints for Cable Box or Satellite Box

Setup

Connections

Please refer to “Basic TV Connection” on the front page before you use this unit.

RF Output Channel

If channel 3 is already occupied for broadcasting,

1)Set your TV to channel 4.

2)Insert a pre-recorded tape into this unit.

3)Press [OUTPUT] on the unit so that the VCR OUTPUT light is lit.

•If noise appears on the TV screen, press [VCR/TV] on the remote control.

4)Press [PLAY B] once.

5)After a few seconds, press [PLAY B] on the unit for 3 seconds.

•The RF output channel will change to channel 4 from channel 3 and you will see a playback picture.

•When a picture does not appear on the TV screen, repeat step 4).

6)Press [STOP C] to stop playback.

Hint

•The RF output channel may not change when you adjust tracking during playback. In this case, stop the playback, and start the playback again. After that, press [PLAY B] on the unit for 3 seconds again.

Setup

Hints for Cable Box or Satellite Box

Connection A (Cable box or				(Back of DVD+VCR)
Antenna or	Satellite box)		ANT-IN
	IN
cable TV		OUT	ANT-OUT	RF cable	E
signal
				(supplied)

(Back of TV)

Select this connection when you want to view or record a scram- bled channel. With this connection, channels cannot be changed on the unit. You can view or record ONLY the channels you have selected on the cable box or the satellite box.

•While you are recording, only the recorded channel can be viewed.

To select channels of the cable box or satellite box

1)Turn on the unit by pressing [POWER], then press [VCR/TV]. The “POWER” light on the front panel will appear, then press [SKIP/CH. i/Kj/L] to select channel 3 or 4 (the same channel as the output channel of the cable box or satellite box).

•If you use the channel 4, you need to change the unit’s RF output to channel 4. Refer to “RF Output Channel”.

2)On the TV, select channel 3 or 4 (the same channel as you have selected at step 1).

3)On the cable box or satellite box, select the channel you want

to view or record.

Connection B		(Back of DVD+VCR)
Antenna or	ANT-IN	(Cable box)
cable TV	ANT-OUT	IN		E
signal			OUT
	RF cable (supplied)		RF cable	(Back of TV)

Select this connection when you want to change channels on the unit. With this connection, you may watch one channel while recording another.

•You may not view or record a scrambled channel.

To select channels of the cable box

1) On the cable box, select channel 3 or 4 (the same channel as the unit’s RF output channel).

•Refer to “RF Output Channel”.

2)On the TV, select the same channel as the output channel (3 or 4) of the cable box.

3)Turn on the unit by pressing [POWER], then press [VCR/TV]. The “POWER” light on the front panel will appear, then select the channel you want to view or record.

To play back a tape

Follow the steps 1) to 2) above, then play back a tape.

•Refer to “Playback” on page 11.

To view one channel while recording another

1)While you are recording on the unit, press [VCR/TV].

2)On the cable box, select the channel you want to view.

Connection to an Audio System

	Method 1
	Stereo system
AUDIO	L	R	Analog audio
			input jacks

Audio cable

(supplied)

DVD+VCR	DIGITAL	AUDIO	S-VIDEO	VIDEO OUT	AUDIO OUT	VCR
		DVD			DVD/VCR
				COMPONENT
	AUDIO OUT	OUT	OUT		L
(Analog)
		L		or
AUDIO OUT					R
		R

(DVD mode only)

Setting	SETUP > AUDIO menu >
Connection	DOLBY DIGITAL
Connecting to Stereo System.	PCM

* To complete these settings, refer to pages 20-21.

Hint

•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

Need help? Call 1-800-813-3435

Method 2

Dolby Digital decoder,

MD deck or DAT deck

	COAXIAL	Digital audio
		input jack
Audio Coaxial
Digital cable
(commercially
available)
		DVD
	DIGITAL	AUDIO S-VIDEO	COMPONENT
			VIDEO OUT
AUDIO OUT		OUT OUT
DIGITAL
AUDIO OUT	COAXIAL
Connection	Setting		SETUP > AUDIO menu >
			DOLBY DIGITAL
Connecting to a Dolby Digital decoder			BITSTREAM
for Dolby Digital audio output.

Connecting to the other equipment (an MD deck	PCM
or DAT deck etc.) without Dolby Digital decoder.

* To complete these settings, refer to pages 20-21.

Hint

•The audio source on a disc in a Dolby Digital 5.1 channel surround format cannot be recorded as digital sound by an MD or DAT deck.

•By hooking this unit up to a Multi-channel Dolby Digital decoder, you can enjoy high-quality Dolby Digital 5.1 channel surround sound as heard in the movie theaters.

•Playing a DVD using incorrect settings may generate noise distortion and may also damage the speakers.

– 6 – EN