|
| Remote Control Unit (continued) | ||||||||
|
|
|
|
|
|
|
| |||
Program button For details, see “Setting theTimer”. | ||||||||||
|
| Press this button to select the mode you want to program. | ||||||||
|
|
|
|
|
|
|
|
| ||
TIMER SELECT button | No display : The timer does not operate. | |||||||||
|
|
|
|
| : The air conditioner stops at the set time. | |||||
|
|
|
| |||||||
|
|
|
|
| : The air conditioner starts at the set time. | |||||
|
|
|
|
| : The air conditioner stops and starts, or starts and stops, at the | |||||
|
|
|
|
|
| set times every day. | ||||
|
|
|
|
|
|
|
| |||
MODE selector button Use this button to select the DRY or COOL mode. | ||||||||||
| (DRY) |
|
|
| : The air conditioner reduces the humidity in the room. | |||||
(COOL) |
|
|
| : The air conditioner makes the room cooler. | ||||||
|
|
|
|
|
|
|
| |||
FLAP button Press this button either to select to set the airflow direction to one of the six | ||||||||||
|
| possible positions manually, or to select the sweep function, which moves | ||||||||
|
| the flap up and down automatically. | ||||||||
|
|
|
|
| : The airflow direction can be set manually. (six positions) | |||||
|
|
|
|
| : The flap moves up and down automatically. | |||||
|
|
|
|
|
|
|
|
| ||
| NOTE | When you press the FLAP button, the air flow direction will be changed one | ||||||||
|
| by one as follows. | ||||||||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
| Swing |
| ||||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
FAN SPEED selector button |
|
|
| : The air conditioner automatically decides the fan speeds. | ||||||
|
|
|
|
| : High fan speed | |||||
|
|
|
|
| : Medium fan speed | |||||
|
|
|
|
| : Low fan speed | |||||
|
|
|
|
|
|
|
|
|
| |
1 HR. TIMER button |
|
|
| : When you press this button, regardless of whether the unit is | ||||||
|
|
|
| operating or stopping, the unit operates for one hour and then | ||||||
|
|
|
|
| shuts down. |
| ||||
ACL button (ALL CLEAR) Puts the remote control unit into | ||||||||||
|
| button after replacing the batteries. | ||||||||
|
|
|
|
|
|
|
|
| ||
ADDRESS switch | • Change the address switch to prevent mixing of signals from remote control | |||||||||
|
|
| units when two Sanyo air conditioners are installed next to each other. | |||||||
|
|
| Normally, the address switch is set to A. When switching the address, the | |||||||
|
|
| remote control must be changed, and the jumper cables on the indoor unit | |||||||
|
|
| board must be cut. For more information, please contact the dealer where | |||||||
|
|
| you made the purchase. |
•Normally, the tabs on the remote control unit should not be bent.
SENSOR button When you press this button (use a
NOTE If the remote control is located near a heat source, such as a space heater or in direct sunlight, press the SENSOR button to switch to the sensor on the indoor unit.
NOTE
The remote control unit sends the temperature signal to the air conditioner regularly at five minute intervals. If the signal from the remote control unit stops for more than ten minutes due to the loss of the remote control unit or other trouble, the air conditioner will switch to the temperature sensor which is built into the indoor unit and control the room temperature. In these cases, the temperature around the remote control unit may differ from the temperature detected at the air conditioner’s position.
9 |