Sanyo MCO-19M(UVH) INTRODUCTION

3

INTRODUCTION

■ Read this manual carefully before using the Product and follow the instructions for safety operation.

■ Sanyo disavows any responsibility for safety if the Product is used for other than the intended use or

used with any procedures other than those given in this manual.

■ Keep this manual in a suitable place so that it can be referred to as necessary.

■ The contents of this manual are subject to change without notice for improvement of performance or

functions.

■ Contact a Sanyo sales representative or agent if any page of the manual is lost or the page order is

incorrect.

■ Contact a Sanyo sales representative or agent if any point in this manual is unclear or if there are any

inaccuracies.

■ No part of this manual may be reproduced in any form without the expressed written permission of

Sanyo.

CAUTION

SANYO guarantees the product under certain warranty conditions. SANYO in no way shall be

responsible for any loss of content or damage of content.

Contents

Main CONTENTS Page INTRODUCTION PRECAUTIONS FOR SAFE OPERATION It is imperative that the user complies with this manual as it contains important safety advice. WARNING CAUTION Symbol shows; Be sure to keep this manual in a place accessible to users of this unit. Page WARNING CAUTION LABELS ON THE INCUBATOR ENVIRONMENTAL CONDITIONS INCUBATOR COMPONENTS 10 tray out. Page 12 Control panel and keypad 2 10 buzzer for an upper limit temperature alarm. 1 3 4 Remote alarm terminal INSTALLATION SITE INSTALLATION WARNING Connection of CO2 gas cylinder Connection of N2 (or O2 ) gas cylinder 18 Connection of gas injection nozzle Using the inner door and gastight split doors z PREVENTING CONTAMINATION PRECAUTIONS FOR CULTURES Using the Unlock Key WARNING CORRECT OPERATION LCD PANEL 8 4 1 2 65 Page BASIC OPERATIONS ON CONTROL PANEL BASIC PARAMETERS Setting the chamber temperature, CO 1 and O density Setting the key lock Releasing the key lock Setting the key lock password 1 2 3 4 5 6 7 Page 30 Automatic N 2 (or O2) gas cylinder changeover 3. Open the valves of both gas cylinders. 1 2 3 4 5 6 7 Setting the upper limit alarm temperature ALARM PARAMETERS M 1 a M UV LAMP PARAMETERS Using the UV lamp Precautions when using the UV lamp Setting the UV lamp ON period 1 3. The UV Setting Display will appear. Set the UV Timer for the UV lamp ON period. 2 3 4 5 6 7 M E N U S e t L o g T o o l s Lighting the UV lamp for 24 hours 1 3 4 5 6 OTHER PARAMETERS Setting the date, time, and log interval 1 2 3 4 5 6 7 Page Initial settings (LCD/DAQ parameters) DISPLAYING THE LOG 1 3 4 5 6 O2 density Switched with Up and Down Cursor Temperature CO2 density Transferring data WATER LEVEL SENSOR 45 ROUTINE MAINTENANCE Cleaning the chamber and inner attachments WARNING 46 Page Filling the humidifying pan H2O2 DECONTAMINATION Page H 2O2 decontamination Page Page Precautions when handling H2O2 decontamination reagent ALARMS, SAFETY, AND SELF-DIAGNOSIS changeover cylinder empty r Alarm o Page Table 2: Alarm and Safety Functions for H2O2 Decontamination Failure during H2O2 decontamination Failure during H2O2 gas analysis by UV Table 3: Alarm and Safety Functions for automatic CO2 and O2 density calibration CALIBRATION 1 Temperature/CO2/O2 calibration Page TROUBLESHOOTING 61 DISPOSING OF THE MULTI-GAS INCUBATOR Page Page 65 (Italian) Page 67 AUTOMATIC CO2 CYLINDER CHANGEOVER 3. Open the valves of both gas cylinders. 1 2 3 4 5 6 7 Page AUTOMATIC CO AND O 1 DENSITY CALIBRATION 2 3 4 5 6 7 1 3 4 5 6 Page STACKING INCUBATORS Front SPECIFICATIONS PERFORMANCE Safety check sheet