ALARMS & SAFETY FUNCTIONS
This unit has the alarms and safety functions shown in Table 7, and also self diagnostic functions.
Table 7. Alarms and safety functions
Alarm | Situation | Indication | Buzzer | Safety functions | |
High temperature | If the chamber temperature is higher |
|
|
| |
than the temperature at which the |
|
|
| ||
alarm | Alarm lamp is flashed. |
|
| ||
high temperature alarm is activated. | Intermittent tone with | Remote alarm with 15 | |||
| Temperature indicator is | ||||
| If the chamber temperature is lower | 15 minutes delay. | minutes delay. | ||
Low temperature | flashed. | ||||
than the temperature at which the |
|
| |||
alarm |
|
|
| ||
low temperature alarm is activated. |
|
|
| ||
|
|
|
| ||
Power failure alarm | When the power to the unit is | Alarm lamp is flashed. | Intermittent tone | Remote alarm. | |
| disconnected. |
|
|
| |
Filter alarm | When the condenser filter is clogged. | Filter lamp lights. | Intermittent tone | ||
|
|
|
|
| |
Battery check | When about 3 years has passed with | Battery check lamp lights. | |||
power switch ON. | |||||
|
|
|
| ||
Fan motor check | When about 6 years has passed with | Battery check lamp | |||
power switch ON. | flashes. | ||||
|
|
| |||
When there is no key pressing in | Chamber temperature is | Finishing of each | |||
each set mode for 90 seconds. | displayed. |
| set mode. | ||
|
| ||||
Key lock | When the key lock is ON. | Change of setting is | |||
disable. | |||||
|
|
|
| ||
|
| Alarm lamp is flashed. |
| Remote alarm. | |
| If the thermal sensor is disconnected. | E01 and chamber temp. are | Intermittent tone | Unit keeps continuous | |
|
| displayed alternately. |
| running. | |
|
| Alarm lamp is flashed. |
| Remote alarm. | |
| If the thermal sensor is | E02 and chamber temp. are | Intermittent tone | Unit keeps continuous | |
|
| displayed alternately. |
| running. | |
| If the cascade sensor is disconnected. | Alarm lamp is flashed. | Intermittent tone | Remote alarm. | |
| E03 and chamber temp. are | ||||
|
| displayed alternately. |
|
| |
| If the cascade sensor is short | Alarm lamp is flashed. | Intermittent tone | Remote alarm. | |
| E04 and chamber temp. are | ||||
| circuited. | ||||
Sensor abnormality | displayed alternately. |
|
| ||
|
|
| |||
If the filter sensor is disconnected. | Alarm lamp is flashed. | Intermittent tone | Remote alarm. | ||
| |||||
| E05 and chamber temp. are | ||||
|
| displayed alternately. |
|
| |
| If the filter sensor is | Alarm lamp is flashed. | Intermittent tone | Remote alarm. | |
| E06 and chamber temp. are | ||||
|
| displayed alternately. |
|
| |
| If the ambient temperature sensor is | Alarm lamp is flashed. | Intermittent tone | Remote alarm. | |
| E07 and chamber temp. are | ||||
| disconnected. | ||||
| displayed alternately. |
|
| ||
|
|
|
| ||
| If the ambient temperature sensor is | Alarm lamp is flashed. | Intermittent tone | Remote alarm. | |
| E08 and chamber temp. are | ||||
| |||||
| displayed alternately. |
|
| ||
|
|
|
| ||
Battery switch | When the battery switch is OFF during | Alarm lamp is flashed. | |||
check | alarm test. | E09 is flashed. | |||
|
| ||||
Condenser temp. | In the event of failure of fan motor for | E10 and chamber temp. |
| Remote alarm. | |
Intermittent tone | Compressor of high | ||||
abnormality | cooling the compressor | are displayed alternately. | |||
| stage side stops. | ||||
|
|
|
|
Note:
•When the operation is started in high ambient temperature, the filter lamp is sometimes flashed. In this case, the lamp is off automatically when the chamber temperature is getting lower.
•The freezer resumes the operation after power failure with the temperature setting before power failure as the chamber temperature setting and alarm temperature setting are memorized in the nonvolatile memory.
•The battery for power failure alarm is an article for consumption. It is recommended that the battery will be replaced about every 3 years. Contact Sanyo sales representative or agent at the time of replacement of the battery for recycling.
•Fan motors are expendable supplies. Replace them for about every 6 years. Contact Sanyo sales representative or agent at the time of replacement of the fan motor.
•The chamber temperature is displayed for 5 seconds by pressing alarm buzzer stop key (BUZZER) during power failure alarm. The alarm lamp keeps flashing.
-61 -
19