Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST9146703SS, ST9300603SS, ST9300503SS, ST9300403SS manual Installation, Drive orientation

Models: ST9146803SS ST9300603SS ST9300503SS ST9146603SS ST9146703SS ST9300403SS

1 78

Download 78 pages 11.24 Kb

Page 52

11.0Installation

11.0Installation

Savvio disc drive installation is a plug-and-play process. There are no jumpers, switches, or terminators on the drive.

SAS drives are designed to be used in a host system that provides a SAS-compatible backplane with bays designed to accommodate the drive. In such systems, the host system typically provides a carrier or tray into which you need to mount the drive. Mount the drive to the carrier or tray provided by the host system using four M3 x 0.5 metric screws. When tightening the screws, use a maximum torque of 4.5 in-lb +/- 0.45 in-lb. Do not over-tighten or force the screws. You can mount the drive in any orientation.

Note. SAS drives are designed to be attached to the host system without I/O or power cables. If you intend the use the drive in a non-backplane host system, connecting the drive using high-quality cables is acceptable as long as the I/O cable length does not exceed 4 meters (13.1 feet).

Slide the carrier or tray into the appropriate bay in your host system using the instructions provided by the host system. This connects the drive directly to your system’s SAS connector. The SAS connector is normally located on a SAS backpanel. See Section 12.4.1 for additional information about these connectors.

Power is supplied through the SAS connector.

The drive is shipped from the factory low-level formatted in 512-byte logical blocks. You need to reformat the drive only if you want to select a different logical block size.

Figure 27. Physical interface

11.1Drive orientation

The drive may be mounted in any orientation. All drive performance characterizations, however, have been done with the drive in horizontal (discs level) and vertical (drive on its side) orientations, which are the two pre- ferred mounting orientations.

44	Savvio 10K.3 SAS Product Manual, Rev. G

Image 52

Seagate ST9146703SS, ST9300603SS, ST9300503SS, ST9300403SS, ST9146803SS, ST9146603SS manual Installation, Drive orientation

Contents

ST9300603SSST9300503SS ST9146803SSST9146703SS ST9300403SS ST9146603SSSavvio 10K.3 SAS Product ManualPage Contents 1.0 Seagate Technology support services 2.0 Scope5.0 Performance characteristics 6.0 Reliability specifications10.0 Defect and error management 11.0 Installation8.0 About FIPS 9.0 About self-encrypting drives 12.0 Interface requirementsSavvio 10K.3 SAS Product Manual, Rev. G Savvio 10K.3 SAS Product Manual, Rev. G List of Figures Page 1.0 Seagate Technology support services SEAGATE ONLINE SUPPORT and SERVICES2.0 Scope Model NumberSelf-Encrypting Drive SED FIPS 140-2 Level 2 certified3.0 Applicable standards and reference documentation 3.1 Standards3.1.1 Electromagnetic compatibility 3.1.1.1 Electromagnetic susceptibility3.1.2 Electromagnetic compliance Electromagnetic compliance for the European UnionAustralian C-Tick Korean MICReference documents 3.1.3 European Union Restriction of Hazardous Substances RoHS4.0 General description 4.1 Standard features 4.2 Media description4.3 Performance 4.4 Reliability4.5 Formatted capacities 4.6 Programmable drive capacity4.7 Factory-installed options 5.0 Performance characteristics 5.1 Internal drive characteristics5.2 Seek performance characteristics 5.2.1 Access time5.3 Start/stop time 5.2.2 Format command execution time for 512-byte sectors minutes5.2.3 General performance characteristics ST9300603SS5.5 Cache operation 5.4 Prefetch/multi-segmented cache control5.5.1 Caching write data 5.5.2 Prefetch operation 6.0 Reliability specifications 6.1 Error rates6.1.1 Recoverable Errors 6.1.2 Unrecoverable Errors6.2 Reliability and service 6.1.3 Seek errors6.1.4 Interface errors 6.2.2 Preventive maintenanceMaximum processing delay On-line only delayFully-enabled delay 6.2.4 S.M.A.R.TTable 1 Temperature Log Page 0Dh Predictive failures6.2.5 Thermal monitor Parameter Code6.2.6.2.1 State of the drive prior to testing 6.2.6 Drive Self Test DST6.2.6.1 DST failure definition 6.2.6.2 Implementation6.2.6.2.3 Short and extended tests Short test Function Code 001bExtended test Function Code 010b 6.2.6.2.4 Log page entriesShipping 6.2.7 Product warrantyProduct repair and return information 7.1 AC power requirements 7.0 Physical/electrical specifications7.2 DC power requirements Savvio 10K.3 SAS Product Manual, Rev. G 3 See +12V current profile in Figure 7.2.2 Power sequencing General DC power requirement notes7.2.1 Conducted noise immunity 7.2.3 Current profiles Figure 17. Current profiles for 300GB modelsFigure 18. Current profiles for 146GB models 7.3 Power dissipation 300 GB models in 3 Gbit operation300GB models in 6 Gbit operation 146GB models in 3 Gbit operation 7.4.1 Temperature a. Operating 7.4 Environmental limits146GB models in 6 Gbit operation Figure 23. Location of the HDA temperature check point 7.4.2 Relative humidity7.4.3 Effective altitude sea level a. Operating 7.4.4 Shock and vibrationPackaged/product weight 7.4.4.1 ShockPackage size Drop height7.4.4.2 Vibration a. Operating-normal Figure 24. Recommended mounting7.4.5 Air cleanliness 7.4.6 Corrosive environment7.4.7 Acoustics 7.4.8 Electromagnetic susceptibilityFigure 25. Mounting configuration dimensions 7.5 Mechanical specificationsin mm in mm Purpose 8.0 About FIPSLevel 2 security 9.2 Controlled access 9.0 About self-encrypting drives9.1 Data encryption 9.2.1 Admin SP9.3 Random number generator RNG 9.4 Drive locking9.5 Data bands 9.2.3 Default password9.7 Authenticated firmware download 9.8 Power requirements9.9 Supported commands 9.6 Cryptographic erase10.1 Drive internal defects/errors 10.0 Defect and error management10.2 Drive error recovery procedures 10.3 SAS system errors Table 4 Read and write retry count maximum recovery timesMaximum recovery time per Maximum recovery time per10.5 Media Pre-Scan 10.4 Background Media Scan10.6 Deferred Auto-Reallocation 10.7 Idle Read After Write 11.0 Installation 11.1 Drive orientation11.2 Cooling Figure 28. Air flow11.4 Grounding 11.3 Drive mountingK x X = F 15lb = 67N 12.1 SAS features 12.0 Interface requirements12.1.1 task management functions SAS task management functions supported12.2 Dual port support 12.3 SCSI commands supported Supported commandsSupported commands Supported commands Supported commands 12.3.2 Mode Sense data 12.3.1 Inquiry dataSavvio inquiry data BytesCHG = Changeable bits indicates if default value is changeable 3. Current values4. Changeable values Savvio 10K.3 SAS Product Manual, Rev. GTable 9 Mode Sense data for 300GB drives Table 10 Mode Sense values for 146GB drives Savvio 10K.3 SAS Product Manual, Rev. GMiscellaneous features 12.4 Miscellaneous operating features and conditionsMiscellaneous status 12.4.1 SAS physical interface Figure 29. Physical interfaceFigure 30. SAS device plug dimensions C OF DATUM BFigure 31. SAS device plug dimensions detail TO DATUM A12.4.2 Physical characteristics 12.4.3 Connector requirements12.4.4 Electrical description 12.4.5 Pin descriptions12.5 Signal characteristics 12.4.7 Power12.4.6 SAS transmitters and receivers 12.5.1 Ready LED Out12.6 SAS-2 Specification compliance 12.7 Additional informationLED drive signal 12.5.2 Differential signalsSavvio 10K.3 SAS Product Manual, Rev. G Numerics IndexPage Page See also cooling Page Seagate Technology LLC