Manuals / Seagate / Computer Equipment / Computer Drive

Seagate ST1000DM003, STBD3000100, STBD2000101, ST2000DM001, ST1500DM003, ST3000DM001 Drive mounting

Models: ST2000DM001 STBD2000101 ST1500DM003 100686584 ST1000DM003 STBD3000100 ST500DM002 ST320DM000 ST3000DM001 ST750DM003 ST250DM000 ST3500320ASIM

1 44

Download 44 pages 31.44 Kb

Page 26

Image 26

Configuring and Mounting the Drive

www.seagate.com

Figure 1 Attaching SATA cabling

Signal connector

Power connector

Signal cable

Power cable

Each cable is keyed to ensure correct orientation. Barracuda drives support latching SATA connectors.

3.4Drive mounting

You can mount the drive in any orientation using four screws in the side-mounting holes or four screws in the bottom-mounting holes. Refer to Figure 2, Figure 3, and Figure 4 for drive mounting dimensions. Follow these important mounting precautions when mounting the drive:

•Allow a minimum clearance of 0.030 inches (0.76mm) around the entire perimeter of the drive for cooling.

•Use only 6-32 UNC mounting screws.

•The screws should be inserted no more than 0.150 inch (3.81mm) into the bottom or side mounting holes.

•Do not overtighten the mounting screws (maximum torque: 6 inch-lb).

Figure 2 Mounting dimensions (3-disk: 3TB, 2TB; 2-disk: 2TB, 1.5TB models)

Temperature

Check Point

26	Barracuda SATA Product Manual, Rev. G

Page 26

Image 26

Seagate ST1000DM003, STBD3000100, STBD2000101, ST2000DM001, ST1500DM003, ST3000DM001, ST250DM000, 100686584 manual Drive mounting

Contents

ST3000DM001 ST2000DM001 ST1500DM003 ST1000DM003 ST750DM003 ST500DM002 BarracudaProduct Manual ST320DM000 ST250DM000Date Document Revision HistoryRevision Description of Change2.0 Drive Specifications ContentsSeagate Technology Support Services 1.0 Introduction 3.0 Configuring and Mounting the DriveBarracuda SATA Product Manual, Rev. G Mounting dimensions 1-disk 1TB and 750GB models FiguresMounting dimensions 3-disk 3TB, 2TB 2-disk 2TB, 1.5TB models Mounting dimensions 1-disk 500GB, 320GB and 250GB modelsBarracuda SATA Product Manual, Rev. G Seagate Technology Support Services Barracuda SATA Product Manual, Rev. G 1.0 Introduction 1.1 About the SATA interfaceBarracuda SATA Product Manual, Rev. G Introductionsets of shadow registers. This is not a typical SATA environment 2.0 Drive Specifications 2.1 Specification summary tablessupport.seagate.com/customer/warrantyvalidation.jsp Drive SpecificationsDrive Specification ST3000DM001ST500DM002 Drive SpecificationsDrive Specification ST320DM000Drive Specification 2.2 Formatted capacityDrive Specifications ST500DM0022.4 Recording and interface technology 2.2.1 LBA mode2.3 Default logical geometry Typical weight 2.5 Physical characteristics2.6 Seek time Maximum height2.7 Start/stop times 2.8 Power specifications2.8.1 Power consumption 3-diskTable 5 DC power requirements 1-disk 1TB and 750GB models Table 3 DC power requirements 3-disk 3TB and 2TB modelsTable 4 DC power requirements 2-disk 2TB and 1.5TB models Table 6 DC power requirements 1-disk 500, 320 and 250GB models2.8.3 Voltage tolerance 2.8.4 Power-management modes2.8.2 Conducted noise Power modes2.9.3 Humidity 2.9 Environmental specifications 2.9.1 Ambient temperature2.9.2 Temperature gradient 2.9.4 Altitude2.9.5.2 Non-operating shock 3TB, 2TB and 1.5TB models 2.9.6 Non-operating vibration2.10 Acoustics 1TB, 750GB, 500GB, 320GB and 250GB models2.10.1 Test for Prominent Discrete Tones PDTs 2.12 Warranty2.13 Agency certification 2.13.1 Safety certification 2.11 Electromagnetic immunityKorean RRL 2.13.2 Electromagnetic compatibility2.13.3 FCC verification Australian C-Tick N1762.15 Corrosive environment 2.14 Environmental protection2.14.2 China Restriction of Hazardous Substances RoHS Directive 3.2 Configuring the drive 3.0 Configuring and Mounting the Drive3.1 Handling and static-discharge precautions 3.3 SATA cables and connectors3.4 Drive mounting Temperature Check Point Configuring and Mounting the DriveFigure 3 Mounting dimensions 1-disk 1TB and 750GB models Barracuda SATA Product Manual, Rev. GRecommended case temperature measurement location Configuring and Mounting the DriveFigure 4 Mounting dimensions 1-disk 500GB, 320GB and 250GB models Barracuda SATA Product Manual, Rev. G4.1 Hot-Plug compatibility 4.2 SATA device plug connector pin definitions4.0 SATA Interface 4.3 Supported ATA commands Barracuda SATA Product Manual, Rev. G Table 10 SATA standard commands continuedSATA Interface Note Individual Set Max Address Table 10 SATA standard commands continuedSATA Interface Barracuda SATA Product Manual, Rev. G4.3.1 Identify Device command xxxxH Table 11 Identify Device commands continuedSATA Interface xx07HxxxxH Table 11 Identify Device commands continuedSATA Interface xxxxHBarracuda SATA Product Manual, Rev. G WordSATA Interface 4.3.2 Set Features command Table 12 Set Features commandS.M.A.R.T. command 4.3.3 S.M.A.R.T. commandsCode in features register Index Page Page Page Page AMERICAS Seagate Technology LLCPublication Number 100686584, Rev. G October ASIA/PACIFIC