Manuals / Sears / Household Appliance / Garage Door Opener

Sears 139.53930D owner manual Hardware Inventory, Assembly Hardware, Installation Hardware

Models: 139.53930D

1 39

Download 39 pages 63.01 Kb

Page 7

Hardware Inventory

Separate all hardware and group as shown below for the assembly and installation procedures.

ASSEMBLY HARDWARE

Lock Nut	Lock Washer	Nut
1/4"-20 (2)	3/8" (1)	3/8" (1)

i

Bolt 1/4"-20xl-3/4" (2)

Master
Link (2)	Idler Bolt (1)

Trolley Threaded Shaft (1)

Carriage Bolt	Wing Nut
1/4"-20xl/2" (2)	1/4"-20 (2)

Lag Screw 5/16"-9xl -5/8" (2)

Lag Screw

5/16"-18xl -7/8" (2)

Carriage Bolt 5/16"-18x2-1/2" (2)

Clevis Pin 5/16"x1-1/2"(1)

INSTALLATION	HARDWARE
		©
Ring		Nut 5/16"-18	(8)	Handle
Fastener (3)		©
Hex Bolt		©		Insulated
Hex Bolt				Insulated
5/16"-18x7/8"	(4)	LockWasher	5/16" (7)	Staples (30)

Screw
6ABx1-1/4" (2)	Screw 6-32xl" (2)

Rope

Drywall Anchors (2)	Spacer	(2)
ol		q
Clevis Pin	Clevis Pin
5/16"x1" (1)	5/16"x1-1/4"	(1)

Image 7

Sears 139.53930D owner manual Hardware Inventory, Assembly Hardware, Installation Hardware

Contents

315N= Garage Door Opener Abridor DE Puerta DE Cochera 315.= Introduction ContentsPreparing your garage door Tools neededSectional Door Installations Sectional Door InstallationPlanning ONE-PIECE Door Without Track ONE-PIECE Door InstallationsONE-PIECE Door with Track Secu RITY,I Carton InventoryInstallation Hardware Assembly HardwareHardware Inventory Assemble the Rail & Install the Trolley Assembly StepFasten the Rail to the Motor Unit Install the Idler PulleyInstall the Chain/Cable Readand Followall Installationwarnings and Instructions InstallationTighten Chain Determine the Header Bracket Location Installation StepWall Header Bracket Installation Install the Header BracketCeiling Header Bracket Installation Attach the Rail to the Header Bracket Sectional Door or ONE-PIECE Door with Track Position the OpenerFinished Ceiling Hang the OpenerUntil the sensor beam is connected and properly aligned Install the Door ControlAttach the Emergency Release Rope and Handle Install the LightElectrical Requirements Important Information about the Safety Reversing Sensor Install The Protector SystemFloor installation Figure Installing the BracketsGarage door track installation preferred Wall installationTroubleshooting the Safety Reversing Sensors Aligning the Safety Reversing SensorsSensors Step Fasten the Door BracketSectional Doors ONE-PIECEDOORS Sectional Doors only Connect Door Arm to TrolleyConnect the door arm to the trolley Adjustment procedures, FigureALL ONE-PIECE Doors Assemble the door arm, FigureIf the door does not close completely Adjustment StepAdjust the UP and Down Travel Limits If door does not open at least 5 feet 1.5 mHOW and When to Adjust the Forces Adjust the ForceTest the Down close force Test The Protector System Test the Safety Reversal SystemAdjust Important Safety CheckNo Oneshouldgoundera STOPPED,PARTIALLY Openeddoor Using Your Garage Door OpenerOperation Readand Followall Warningsand InstructionsTo RE-CONNECT the Trolley Using the Wall.Mounted DoorControl To Open the Door Manually Disconnect the TrolleyRemote Control Battery AdjustmentsCare of Your Garage Door Opener Refer to Adjustment , Adjust the Force Having a PROBLEM?Symptom Motor unit doesnt operate Symptom LED is not fit on door controlTo Erase All Codes From Motor Unit Memory To Add or Reprogram a Hand.held Remote ControlUsing the Learn Button ProgrammingTo change an existing, known PIN To Add, Reprogram or Change a Keyless Entry PINTo set a temporary PIN KEY Part Description Repair PartsRail Assembly Parts Installation PartsKEY Part NO. no Motor Unit Assembly PartsKEY Part Description Warranty Accessories