INSTALLATION STEP 6

Install the Door Control

Locate door control within sight of door, at a minimum height of 5 feet where small children cannot reach, away from moving parts of door and door hardware. If installing into drywall, drill 5/32" holes and use the anchors provided. For pre-wired installations (as in new home construction), it may be mounted to a single gang box (Figure 2).

1.Strip 7/16" of insulation from one end of bell wire and connect to the two terminal screws on back of door control by color: white wire to 2 and white/red wire to 1.

2.Door Control Button: Fasten securely with 6ABx1-1/2" screws.

Console Model: Pry off cover along one side with a screwdriver blade (see Figure 1). Fasten with 6ABx1-1/4" self-tapping screws (standard installation) or 6-32x1" machine screws (into gang box) as follows:

WARNING

To prevent possible SERIOUS INJURY or DEATH from electrocution:

•Be sure power is not connected BEFORE installing door control.

•Connect ONLY to 24 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

•Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet, and away from all moving parts of door.

•NEVER permit children to operate or play with door control push buttons or remote control transmitters.

•Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

•ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

• Install bottom screw, allowing 1//8" to protrude

above wall surface.

• Position bottom of door control on screw head and

slide down to secure. Adjust screw for snug fit.

• Drill and install top screw with care to avoid

cracking plastic housing. Do not overtighten.

• Insert top tabs and snap on cover.

3. (For standard installation only) Run bell wire up

wall and across ceiling to motor unit. Use insulated

staples to secure wire in several places. Do not

pierce wire with a staple, creating a short or open

circuit.

4. Connect the bell wire to the terminal screws on the

Outside Keylock Accessory Connections

To opener terminal screws: white to 2; white/red to 1

 

HARDWARE SHOWN

6AB x 1-1/2" Screw

ACTUAL SIZE

 

Door Control Button

 

6AB x 1-1/4" Screw

Insulated

Control Console (std installation)

Staples

6-32 x 1" Screw

 

Control Console (pre-wired)

Dry Wall Anchors

motor unit panel: white to 2; white/red to 1.

5. Position the antenna wire as shown.

6. Use tacks or staples to permanently attach

entrapment warning label to wall near door control,

and manual release/safety reverse test label in a

prominent location on inside of garage door.

NOTE: DO NOT connect power and operate opener at this time. The trolley will travel to the full open position but will not return to the close position until the sensor beam is connected and properly aligned.

Figure 1

 

Figure 2

REMOVE & REPLACE COVER

PRE-WIRED

To Replace,

To Remove,

INSTALLATION

 

Insert Top

Twist

 

Tabs First

Here

 

 

LIGHT

 

 

LOCK

 

24 Volt

2-Conductor Bell Wire in Gang Box

WHT 2

1 RED

Terminal

Screws

 

 

Lighted

 

 

Push Button

 

 

Top

 

 

Mounting

 

 

Hole

 

WHITE

Terminal

 

2

 

 

Screws

Bell

RED

L

 

 

IGHT

Wire

1

Bottom

Bell

Mounting

 

 

Hole

 

Wire

 

 

2-Conductor

Opener

Bell Wire

Terminal Screws

 

1

2

 

 

3

 

9

1

9

1

Light

7

3

7

3

5

 

 

5

KG

 

 

KG

LOCK

Lock

(BACK VIEW)

(BACK VIEW)

DOOR CONTROL BUTTON

PREMIUM CONTROL CONSOLE

Back Panel

of Opener

Antenna

18