GENERAL RECOMMENDATIONS | BEFORE EACH USE |
The warranty of the high pressure washer does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain high pressure washer as instructedin this manual.
Some adjustments will need to be made periodically to properly maintain your high pressure washer.
All adjustments in the Service and Adjustments sec- tion of this manual should be made at least once each season.
oOnce a year you should clean or replace the spark plug and clean or replace the air filter and check the gun and wand assembly for wear. A new spark plug and clean air filter assure proper
PRODUCT SPECIFICATIONS
Pressure Washer Specifications
PRESSURE | 1650 psi | |
FLOWRATE | 2 GPM | |
DETERGENTMIX | Use undiluted deterqent.... | |
WATER SUPPLY |
| |
TEMPERATURE | Not to Exceed 140°F | |
Engine Specifications |
| |
ENGINE MODEL | Briq,qs& Stratton | |
,RATED HORSEPOWER | 3.8 | |
DISPLACEMENT | t58cc | |
SPARK PLUG: Type: | Champion | |
|
| or equivalent |
| Set Gap to: | 0,030 inch (0,76turn) |
: GASOLINE CAPACITY | 1 U.S. Quart | |
[ *"'"', .... | , | SAE 30 weight |
. Q!L (20 oz. capacity) | ||
SOLID STATE IGNITION | 0.0125 inch | |
AIR GAP |
|
|
In the State of California a spark arrestor is required
by law (Section 4442 of the California Public Resources Code). Other states may have similar
laws. Federal laws apply on federal lands.
Note: If you equip the engine of your pressure wash- er with a spark arrestor muffler, the spark arrestor must be maintained in effective working order by the
owner/operator.
You can order a spark arrestor through your Sears Service Center.
=Check water inlet screen for damage. - Check high pressure hose for leaks.
• Check detergent inlet hose and filter for damage.
• Check gun and wand assembly for teaks.
•Purge pump of air and contaminants.
,Check engine oil level.
PRESSURE WASHER MAINTENANCE
Check and Clean Inlet Screen: Remove
tor. Clean if it is clogged or replace if it is torn.
Check High Pressure Hose: High pressure hose can develop leaks from wear, kinking, abuse. Inspect hose each time before using it. Check for cuts, leaks, abrasions or bulging of cover, or damage or move- ment of couplings. If any of these conditions exist, replace hose immediately.
Check Detergent Hose: Examine the filter on the detergent hose and clean if clogged. Hose should fit tightly on barbed fitting. Examine hose for leaks or tears. Replace the filter or hose if either is damaged.
A DANGER: Water spraying from a leak is capable of injecting material into skin. NEVER repair high pressure hose. Replace with hose that meets minimum pressure rating of your pressure washer.
Check Gun and Wand: Examine hose connection to gun and make sure it is secure. Test trigger by press- ing it and making sure it springs back into place when you release it. Put safety latch in UP position and test trigger. You should not be able to press trigger.
Purge Pump of Air and Contaminants
To remove the air from the pump, follow these steps:
=Set up the pressure washer as described in the ASSEMBLY section and connect the water sup- ply.
-Remove the wand extension from the gun.
-Pull the trigger on the gun and hold.
To remove the contaminants from the pump, follow these steps:
°Set up the pressure washer as described in the ASSEMBLY section, and connect the water sup- ply.
•Remove the nozzle attachment from the gun.
°Start the engine according to instructions in OPERATION section.
°Pull the trigger on the gun and hold.
•When the water supply is steady and constant, engage the safety latch and refasten the nozzle attachment.
11
