..................................M.............
TROU LES OOTING POINTS
PROBLEM | CAUSE | CORRECTION |
|
|
i,,,Ull: | ,hi, ill,i ,,, ,;,i n | ,,,,,,,,,,,,, | .,,,.,,, | , ,,, |
|
|
|
Does not start
Loss of power
Poor cut - uneven
Excessive vibration
Starter rope hard to pull
...... ,,,,
1.Dirty air filter, 2, Out of fuel,
3.Stale fuel.
4, Water in fuel,
5.Spark ptug wire is disconnected.
6.Bad spark plug,
7.Loose blade or broken btade adapter,
8.Control bar in released position
9.Control bar defective
t.Rear of lawn mower housing/blade dragging
in heavy grass.
2.Cutting too much grass.
3.Dirty air filter.
4.Buildup of grass, leaves and trash under mower.
5.Too much oil in engine.
6.Walking speed too fast.
t.Worn, bent or loose blade, 2, Wheel heights uneven,
3.Low engine speed,
4.Buildup of grass, teaves, and trash under mower,
t.Worn, bent or ioose blade,
2.Bent engine crankshaft.
1.Engine flywheel brake is on when control bar is released.
2.Bent engine crankshaft
3.Blade adapter broken.
4.Blade dragging in grass.
1, clean/replace air filter.
2.Fill fuel tank.
3.Drain tank and refill with fresh clean fuel
4.Drain fuel tank and carburetorand refill tank with fresh gasofine,
5.Connect wire to plug.
6.Replace spark plug,
7.Tighten blade bolt or replace blade adapter.
8.Depress control bar to handle.
9.Replace control bar.
1.Set in "Higher Cut" position.
2.Set in "Higher Cut 'position.
3.Clean/replace air filter.
4, Clean underside of mower housing, 5, Check oil level,
6.Cut at slower walking speed,
__,,_,÷ | _ |
t.Replace blade, Tighten blade bolt,
2.Set all wheels at same height,
3.Set engine speed control in HIGH position,
4.Clean underside of mower housing.
1.Replace blade. Tighten blade bolt,
2, Contact Sears Service Department.
1.Depress control bar to upper handle before pulling starter rope.
2.Contact Sears Service Department,
3.Replace blade adapter.
4, Move lawn mower to cut grass or to hard surface to start engine.
Loss of drive | I. | Drive | wheels |
| not turning with drive | control engaged. | 1. | Adjust | or | reptace drive control | cable, if broken, | |||||||
| 2, | Belt | not driving. |
|
| 2. | Put belt on | pulleys or | replace | belts | if broken. | |||||||
Grass catcher not filling | 1. | Cutting | height | too low. |
| t. | Raise | cutting | height. |
|
|
|
| |||||
(If so equipped) | 2. | Lift on | blade | worn off. |
| 2. | Replace | blade. |
|
|
|
| ||||||
| 3, | Catcher not | venting | air. |
| 3. | Clean | grass | catcher. |
|
|
|
| |||||
| 4. | Low | engine | speed. |
|
| 4. | Set engine | speed control | in HIGH | position. | |||||||
Hard to push | t. | Grass | is too high or | wheel height is toe low. | t, | Raise | cutting | height, |
|
|
|
| ||||||
| 2. | Rear of lawn mower | housing/blade | dragging | 2. | Raise | rear of lawn mower | housing | one (1) | |||||||||
|
| in grass. |
|
|
|
|
| setting | higher. |
|
|
|
| |||||
| 3, | Grass | catcher | too ful!. |
| 3. | Empty | grass | catcher, |
|
|
|
| |||||
| 4. | Handte | height | position not right for you. | 4. | Adjust | handle | height | to suit, |
|
|
27