ASSEMBLY INSTRUCTIONS
Tools Needed for Assembly
* pipethread sealant (not incJuded)
,an a,clJustable wrench for attaching the pressure regulator
"a _t_0,socket or open end wrench for attaching the wheels and hose adaptan
"a 7/1_open and wrench for attaching the air pressure
gauges
,a _e °'he,v.Re'i"for Installing the plug in the regulal_
,a %" open end wrenchto tighten handlescrews
"s #2 philtipe screwdriver for attaching the control cover
installing Wheels, Handle, Rubber Foot Strip
i WARNIN_!
THE WHEELS AND HANDLE OO NOT PRO- VIDE ADEQUATE CLEARANCE, $TABJLITY
OR SUPPORT FOR PULLING THE UNIT UP AND DOWN STAIRS OR STEPS, THE UN[T MUST I_ELtFT]_D, OR PUSHED UP A RAMP.
1.Dipthe handle grip Insoapywater and sttdeintoposi- tionas shownon photoon page 6 or page 12.
2, Attachthe handleto the insideofthecompressorsad- diebyp_jshtngthe handle In,unllithe slotin thehandle engageswith the labs in the saddle, Pufithe handle bsckar<l installthe two s<z_ws,one on each side of the _e_ldte.Tighten securely,
3- Rsmove the protectivepaper strip frOmth_ adhesive backed rubber footstrip,Attachthe rubberfootstrip to the bottom of 1he airtitnk leg. Press firmlyinto place°
4.Attach one wheel to each side of the air ¢omp_ssor. Use one shoulder bott and one nut for each wheel, Tighten securely.
Installing Regulator
Use a small amountof, pipe thread sealant on aJipipe thread joints.
Install the regulatoron 1heend of lhe manifold using the short pipe nipple. The arrow on the bottom ol the regulatOrmust poi_ away from the manifold in order fo_ theregulatorto functionproperly,
_nstalithe adapter and plugIn the regulator,,The plug is supplied with the regulator,Installthe rear cover and the gauges at the same time, See diagram below,
R_ULATEDTANK
PRESSURE GAUG_ PRESSURE GAUGP-
ittory be necemury to brace or support one enU of the outfit when attaching the wheels end the r_Jbber foot _trlp,because the air compressor will have a tenden=y to tip.
tnstallthe control_over. Fasten It to the manifoldusing the phillipsscrew. Installthe plasticmounting ring tothe regulatorto fastenthe top ofthe contmtcover,See photo on page 6.
INSTALLATION AND BREAK-IN PROCEDURES
Locationof the Air Compressor
Loca4ethe air compressorin a ctean,dry end welJventi- latecl area. The air filler must be kept clear o'lobstruc.
tlons which could reduce air delivery of the air compressorThe. air compressorshould be locatedat least 12'away'from the wail or other obstructionsthat wl!linterfere withtheftow of air. The air compressorhead
and shroudare designed to al!ow for propercooling.,If humidity Is high a _ears air filter can be installed iD
remove excessive moisture. Follow the instructions
packaged with the air filter for proper installation,
Lubricationand Oil
Thtsunit n_eas no adcllttonal lubrication or otling
Extension Cords
Use extre,air hose insteaxJOf _n extensioncordto avoid voltagedrop and power loss to the motor,
tf an axlet_slon cordmust t_ us'_,be sum it is:
. a
. t_ good condition_
• no longerthan _50f_t.
.12 gtlUge (AWG) or larger. (Wire size increases as gauge number _lecreaseso10 AWG and 8 AWG may atso l_e used, OO NOT USt_ t4 or 16AWG_)
