SECO-LARM USA SK-1123-FQ warranty Back-Lit Jumper, SECO-LARM U.S.A., Inc, Getting Started

ENFORCER FLUSH-MOUNT OUTDOOR ACCESS KEYPAD

WIRING, BASIC DIAGRAM

The ENFORCER SK-1123-FQ has backlit keys that can be programmed for different applications. The keypad can be always illuminated (FULL), or illuminated only during user activity (AUTO). To verify or change the settings, refer to the table below.

			Back-lit jumper
	1	3
			DAP Jumper
	N.C. tamper		Interlock—NPN transistor, used
			with second keypad2
			(-) N.O. Output 1 inhibit3
	N.C. tamper
12~24V	(+)		(-) N.C. Door position sensor
			(-) Common ground—for use
VAC/VDC	(-)		with interlock function
		EGRESS IN	(-)Egress—N.O. ground 4
	N.C
			Duress output—Transistor
Output 1	COM		ground (-) 100mA@24VDC
			(-) N.O. output 2
	N.O.

Back-Lit Jumper

Setting	Jumper Position					Description
						Keypad standby mode is dimly backlit.
FULL						Keypad brightens to full illumination for 10 seconds
(default)						after each key is pressed, then returns to dim backlit
		1		2	3
						(standby mode).
						Keypad standby mode is not lit.
AUTO						Keypad brightens to full illumination for 10 seconds
						after each key is pressed, then turns off again
			1	2	3
						(standby mode).

1For DC, connect to a regulated power supply. Polarity of the regulated power supply must be correct. For AC, polarity is not important.

2Mantrap control output – Outputs ground (-) for five seconds after relay output #1 is activated, continues while the door is open.

3Connect to ground (-) to prevent relay output #1 from operating, or to the mantrap (interlock) control output of another keypad to disable output #1 while the other keypad is active.

4Connect to optional N.O. push button or switch.

Page 4 SECO-LARM® U.S.A., Inc.

ENFORCER FLUSH-MOUNT OUTDOOR ACCESS KEYPAD

PREPARING TO PROGRAM THE KEYPAD

To program the SK-1123-FQ, first determine the following information:

1.The master code – Allows the system administrator to program or operate the keypad.

2.The user code or codes – Allows users to use the keypad’s functions. Use the chart on pages 8 and 9 to organize.

3.Configuration of the relays and outputs – For relay output #1 and output #2, determine whether the output should operate from 1 to 999 seconds and then turn OFF (momentary mode), or turn

ON/OFF via the code (shunt mode). Use the chart on pages 8 and 9 to organize.

4. Result of improper code entry (optional) – Choose between a 30-second code lockout, duress output, a 15-minute code lockout, or no reaction.

*Note: When x x x x appears in the instructions, it indicates master code entry.

GETTING STARTED

A master code is required to program the keypad. The default master code is set to ―0000.‖ To change a forgotten master code, go to page 15 and follow the instructions for ―MASTER CODE BYPASS‖

(DAP jumper).

Once the master code is set, review the programming options and decide exactly what the keypad will do, including the format of the user access codes as well as how the keypad responds via the relay output, buzzer and LEDs. Note that in every case the basic steps for programming are:

1.Enter the master code, followed by the key, which puts you in programming mode.

2.Enter the programming options defined in the various sections as needed, followed by the # key.

3.Enter the key again to exit programming mode.

Note: A rapid string of 5 beeps and/or 5 LED flashes indicates an error, while 2 beeps indicates that the entry has been accepted.

USER PROGRAMMING

ENTER PROGRAMMING MODE

Enter Master Code					Confirm	Function
	x	x	x	x		Enter into programming mode

ADDING OR CHANGING MASTER AND USER CODES

WARNING – Press the correct option key. If the option key is not used and a “0” is pressed after entering the Master Code, it could accidentally reprogram the Master Code.

Option		User ID	Access Code	Confirm		Function
			4 to 8 digits
	0				#	Change Master Code
		00 to 99	4 to 8 digits			Set/change up to 100 User Codes for output #1, with duress feature
	1				#
		0 to 9	4 to 8 digits			Set/change up to 10 User Codes for output #2
	2				#

Note: User D must be entered for options 1 and 2.

DELETE A USER

To delete a user who no longer has authority to enter the protected area:

Option		User ID	Confirm		Function
		00 to 99			Deletes specific user ID from output #1
	1			#
		0 to 9			Deletes specific user ID from output #2
	2			#

Note: User D must be entered for options 1 and 2.

EXIT THE PROGRAMMING MODE BY PRESSING THE * KEY

SECO-LARM® U.S.A., Inc. Page 13