SECO-LARM USA SK-1123-FQ warranty Enforcer FLUSH-MOUNT Outdoor Access Keypad, LED Indicators

ENFORCER FLUSH-MOUNT OUTDOOR ACCESS KEYPAD

PROGRAMMING NOTES

1.Master Code: The SK-1123-FQ comes pre-programmed with the Master Code set at 0000. Additional codes and/or data should be programmed at the owner’s discretion. However, to ensure security, program a new Master Code to replace the factory-set Master Code as soon as possible.

2.Factory defaults:

ENFORCER FLUSH-MOUNT OUTDOOR ACCESS KEYPAD

SPECIFICATIONS

Power:

Operating voltage – 12~24 Volts AC/DC. No jumper needed to set voltage. Stand-by current drain – 10mA@12VDC.

Master code	0000
User code length	4-8 digits
Output #1 time	1 second
Output #2 time	1 second
Wrong code lockout	10 tries / 30 sec.
Door-forced-open alarm	Disabled

Door-forced-open alarm	Disabled
Door unlocked annunciation	ON
User code entry mode	Manual
Keypress beep	ON
Door-propped-open alarm	OFF
Silent operation	OFF

Active current drain (press keypad key) – Under 45mA@12VDC.

Active current drain (one relay activated) – Under 100mA@12VDC.

Outputs:

Output #1 – 5A@30VDC max. rating, Form ―C dry contact‖, NO/COM /NC. Programmable for 1 to 999 second timed output or shunt (ON/OFF) output. Three terminals.

3.Code operation: User codes are each four to eight digits and are assigned a two-digit ID. If all the codes have the same number of digits, the keypad can be programmed for auto code checking. The # key need not be pressed after entering a code (see programming option 82, page 14, section 7).

The administrator can easily delete the code of a single user via the two-digit ID if the user is no longer authorized to enter a protected area.

Relay output #1 allows up to 100 user codes, and output #2 allows up to 10 user codes.

4.Using Duress codes (relay output #1 only): Duress codes are used to activate a separate device silently to alert a guard or other personnel that a user is operating the keypad under threat. The keypad operates as normal, but a silent signal is sent to alert others.

Duress codes do not need to be programmed. All user codes are automatically turned into duress codes by increasing the first digit of a user code by the number 2. The code is entered the same way as a regular user code.

For example:

User code 4468 can be entered as duress code 6468 User code 9843 can be entered as duress code 1843 User code 8181 can be entered as duress code 0181

NOTE: If a user code is programmed, its duress code is unique and cannot be programmed as another user code. For example:

If user code 4468 is programmed, its duress code of 6468 is automatically programmed. A user code of 6468 cannot be programmed.

Note: Once activated, the duress output continues until a correct user code is entered.

LED INDICATORS

Red LED – Illuminates while output #2 is activated.

Amber LED – Flashes to show the keypad status (see below).

Green LED – Illuminates while output #1 is activated.

BUZZERS AND LED SIGNALS

				Red Amber Green
	STATUS	BUZZER TONES*	AMBER LED FLASHES
1.	In programming mode	---	ON
2.	Successful key entry	1 beep	1 flash
3.	Successful code entry	2 beeps	2 flashes
4.	Unsuccessful code entry	5 beeps	5 flashes
5.	DAP jumper not replaced	Continuous beeps	Continuous flashes
6.	In standby mode	---	1 flash in 2-sec intervals
7.	Output relay activated	1-sec long beep**	---

NOTE: *The buzzer can be disabled through programming option 83, see pg. 14, section 8.

**The output relay activated beep can be disabled through programming option 81, see pg. 14, section 6.

Output #2 – 100mA@24VDC max. rating. Transistor ground output programmable for 1 to 999 second momentary output or shunt (ON/OFF) output. One terminal.

Mantrap (interlock) control output – 100mA@24VDC. NPN open collector switches to ground (-) for five seconds after relay output #1 is activated, continues while the door is open. Use to disable a second keypad during this time. Single terminal.

Duress output – 100mA@24VDC. NPN open collector switches to ground when active. Single terminal.

Inputs:

Power – 12~24 Volts AC/DC. Two terminals. Egress – N.O., ground (-). Single terminal.

Door sensor input – N.C., ground (-). Connect to an N.C. magnetic contact to show if door is opened or closed, or connect to ground (-) if not used. Single terminal.

Relay output #1 disable input – Connect to ground (-) to prevent relay output #1 from operating, or to the mantrap (interlock) control output of another keypad to disable output #1 while the other keypad is active. Single terminal.

Other Features:

Tamper – 50mA max., N.C. dry contact. Connect to the tamper circuit of alarm control panel. Two terminals.

Common ground (-).

Code Operation:

Auto or manual code entry. Up to 100 user codes for output #1, up to 10 user codes for output #2. Over 100 million possible user code combinations.

Auto Reset Time During Code Entry:

Max. 10 seconds to enter each digit.

Max. 30 seconds to enter each code.

Dimensions:

43/4‖x31/8‖x115/16‖ (120x80x46 mm)

Weight:

11-oz (300g)

Page 12 SECO-LARM® U.S.A., Inc. SECO-LARM® U.S.A., Inc. Page 5