TS2000
Programmable Ouputs
The programmable outputs from the NU and the REM, are referred to as the Node Outputs and are activated in response to various conditions or events. They are programmed to respond to System, Ward or Circuit activation.
Panel outputs are from the CP and are programmed in the same way as the Node outputs. Outputs 1 to 8 are from the Parallel Interface Board, if fitted, and 9 to 16 are for the DC3 or DC3M Digicom if fitted.
(26)Exit Setting: Final Exit setting is in progress
(27)Exit Error: An error occurred during the exit procedure and the system cannot set
(28)Lock Alert: The programmed Time Lock period is about to start;
(29)Fire/Viper: Will provide 12V (100mA source) to devices which latch when activated and which are unlatched when power is removed. The output is removed for about 3 seconds when unsetting the system after an alarm at the second passcode entry;
(30)PSU Test: Connected to remote PSU to initiate a battery test;
The System activated outputs may be allocated to any | CAUTION: It is essential to ensure that the correct | ||
Node (NU or REM) output or the Panel (CP) outputs. They | outputs that will source (supply) or sink (accept) current | ||
are | designated by their function and may be | are selected to match the function required. | |
programmed to be active if required. The following are |
| ||
available: |
| ||
(1) | Alarm: A system alarm is present; |
| |
Menus Listing in Sequence | |||
(2) | P. A.: A Personal Attack circuit or a Duress Alarm | ||
| |||
| has been activated; | NOTES: | |
(3) | Set: The system is Set; | ||
Users will enter menus at Menu 1 | |||
(4) | Fire: A Fire circuit has been activated; | ||
Engineer will enter menus at Menu 15 | |||
(5) | Medical: A Medical circuit has been activated; | ||
User Level 5 (Standard W) can only set and unset | |||
(6) | Tamper: A Tamper alarm is present; | ||
designated wards | |||
(7) | Aux: An Auxiliary circuit has been activated; | ||
Instant access to Menus from a keyboard number | |||
(8) | Set Fail: An attempt to set the system has failed; | ||
entry applies to Menus 1 to 9 only | |||
(9) | Site Engr: The Engineer’s passcode has been | ||
Menu 2 is only available if a Ward is Set; | |||
| entered. The output will remain active until a | ||
| Menu 7 is only available if there are circuits with | ||
| User passcode is entered; | ||
| attribute omit | ||
(10) | |||
Menu 9 is only available if a printer is connected | |||
| the start of the Time Lock period; | or the SIB is fitted | |
(11) | Menu 17 is only available if a Ward is defined | ||
(12) | AC Alarm: The mains supply to the PSU has not | Menu 24 is only available if a DC3(M) is fitted | |
| been present for the mains fail time period; | Menu 25 is only available if Engineer Reset is | |
(13) | AC Off: The mains supply to the PSU is not | programmed and a reset is required | |
| present or there is no 12V output; | (Passcode) Levels: | |
(14) | Batt Fault: During the PSU test or while the mains | 1 Engineer | |
| is off the PSU Battery voltage is low. | ||
| 2 Master | ||
(15) | Bell: The CP bell output is activated; | ||
3 Manager | |||
(16) | Strobe: The CP strobe output is activated; | ||
4 Standard S | |||
(17) | Switch +12: The system is Set and is not in | ||
5 Standard W | |||
| alarm; | ||
| 6 Restricted | ||
(18) | Walk Test +: A Walk Test is in progress (use output | ||
| |||
A or B);
(19)Walk Test
(20)Line Fault: A Digicom telephone line fault is present;
(21)Time Switch: The programmed Time Switch is active;
(22)Time Locked: The system has been Time Locked and cannot be unset;
(23)Entry Mode: Entry mode has been initiated;
(24)2nd Entry: The first Entry time has timed out before a passcode entry
(25)Exit Mode: System Exit procedure has been initiated;
TS2000 | 18 of 20 | 496529 Issue A |
