Sharp AR-160, AR-161 specifications Value

AR-161

Main	Sub	Contents		Details of operation	Initial	Set range
code	code				value
7	2	Aging without JAM with	Used to start warmup and count and display the warmup time every			1 ~ 99
		warmup time display	second. After completion of warmup, count up is terminated and the
			ready lamp is lighted. When the clear key is pressed and the copy
			quantity is entered and the start key is pressed, copying is made to make
			the set quantity of copies. At that time, the paper size does not matter.
				Key operation
				Copy quantity setting: Numeric keys
	4	Warmup saving	Used to bring the machine to the ready state without warmup.
	6	Intermittent aging (with	After completion of warmup, counting is stopped and the ready lamp is			1 ~ 99
		paper)	lighted. When the copy quantity is entered and the start key is pressed,
			copying is made to make the set quantity of copies. After 3 sec standby,
			copying is made again to make the set quantity of copies. After that this
			operation is repeated. The paper size does not matter.
				Key operation
				Copy quantity setting: Numeric keys
	7	Intermittent aging (without	After completion of warmup, counting is stopped and the ready lamp is			1 ~ 99
		paper)	lighted. When the copy quantity is entered and the start key is pressed,
			copying is made to make the set quantity of copies. After 3 sec standby,
			copying is made again to make the set quantity of copies. After that this
			operation is repeated. The paper size does not matter.
				Key operation
				Copy quantity setting: Numeric keys
	8	Warmup time display	Used to count and display the warmup time from 0 at every second.
8	1	Developing bias voltage	Used to output the developing bias for 30 sec. For the adjustment proce-
		output check	dure of the developing bias, refer to the previous descriptions.
	2	Main charger voltage	Used to output the main charger grid bias voltage at the high mode for
		output check (Grid bias	30 sec. For the adjustment procedure of the main charger grid bias
		high mode)	voltage, refer to the previous descriptions.
	3	Main charger voltage	Used to output the main charger grid bias voltage at the low mode for 30
		output check (Grid bias	sec. For the adjustment procedure of the main charger grid bias voltage,
		low mode)	refer to the previous descriptions.
	6	Transfer charger voltage	Used to output the transfer charger voltage for 30 sec. For the adjust-
		check	ment procedure of the transfer charger voltage, refer to the previous
			descriptions.
9	1	Duplex motor forward	Used to rotate the duplex motor forward for 30 sec.
		rotation operation check
	2	Duplex motor reverse	Used to rotate the duplex motor reversely for 30 sec.
		rotation operation check
	4	Duplex motor rotation	After completion of warmup, the ready lamp is lighted and the currently
		speed adjustment	set duplex motor rotation speed set value is displayed.
			When the set value is entered and the start key is pressed, the set value
			is stored.
				Key operation
				Duplex motor rotation speed set value: Numeric keys
	5	Duplex motor switchback	After completion of warmup, the ready lamp is lighted and the currently
		time adjustment	set duplex motor switchback time set value is displayed.
			When the set value is entered and the start key is pressed, the set value
			is stored.
				Key operation
				Duplex motor switchback time set value: Numeric keys
10		Toner motor operation	Used to operate the toner motor for 30 sec.
		check	Note: If this simulation is executed with the toner hopper installed, toner
				is automatically supplied to the developer. Be careful of overtoner.
14		Trouble (except for U2)	Used to cancel troubles except for U2.
		cancel
16		U2 trouble cancel	Used to cancel U2 trouble.
17		PF trouble cancel	Used to cancel PF trouble.

8 – 4