AR-161

<Adjustment specification>

Mode

Specification

SIM

Set value

Set range

 

 

 

 

 

Original

Single:

SIM

Add 1:

1 ~ 99

off center

Center ± 2.0mm

50-18

0.1mm shift to

 

mode

 

 

R side

 

Duplex:

 

 

(OC mode)

 

Reduce 1:

 

Center ±2.5mm

 

 

 

 

 

0.1mm shift to

 

 

 

 

L side

 

 

 

 

 

 

b. SPF mode

Note: Before performing this adjustment, be sure to check that the paper off center is properly adjusted.

1)Make a test chart for the center position adjustment and set it on the SPF.

<Adjustment specification>

Draw a line on a paper in the scanning direction.

2)Make a normal copy from the manual paper feed tray, and com- pare the copy and the original test chart.

If necessary, perform the following adjustment procedures.

3)Execute SIM 50-16.

4)After warmup, shading is performed and the current set value of the off center adjustment at each paper feed port is displayed on the display section in 2 digits.

5)Enter the set value and press the start key. The set value is stored and a copy is made.

<Adjustment specification>

Mode

Specification

SIM

Set value

Set range

 

 

 

 

 

Original

Single:

SIM

Add 1:

1 ~ 99

off center

Center ± 3.0mm

50-16

0.1mm shift to

 

mode

 

 

R side

 

Duplex:

 

 

(SPF

 

Reduce 1:

 

Center ±3.5mm

 

 

mode)

 

 

0.1mm shift to

 

 

 

 

L side

 

 

 

 

 

 

(8) Original sensor adjustment (SIM 43-3)

1)Execute SIM 41-2.

2)Set A3 (11" x 17") paper on the OC table.

3)Press the start key again.

4)The sensor level of the original sensor is automatically checked and the value with an original - 40 is made as the threshold value for scanning. (Automatic setting)

5)Execute SIM 43-3.

6)The light reception level of the original sensor is displayed.

The first digit of the copy quantity display shows "A": Light recep- tion level display

The first digit of the copy quantity display shows "b": Original judgement level display

(The mode selection is made with the magnification ratio display key.)

7)By changing the paper set on the original table, the original size LED sensed by the sensor is lighted.

C. Image density adjustment

(1) Copy mode (SIM 46-1)

1)Set a test chart (UKOG-0162FCZZ) on the OC table as shown below.

2)Put several sheets of A3 or 11" x 17" white paper on the test chart.

3)Execute SIM 46-1.

4)After warmup, shading is performed and the current set value of the density level is displayed on the display section in 2 digits.

For mode selection, use the density select key.

5)Change the set value with the 10-key to adjust the copy image density.

6)Make a copy and check that the specification below is satisfied.

<Adjustment specification>

Density

Display

Exposure

 

Sharp Gray

Set value

Set

mode

lamp

level

 

Chart output

range

 

 

Auto

Auto

 

"3" is slightly

The greater the

1 ~ 99

 

 

 

 

copied.

set value is, the

 

Manual

Manual

3

 

"3" is slightly

greater the

 

 

 

 

 

copied.

density is.

 

Photo

Photo

3

 

"3" is slightly

The smaller the

 

 

set value is, the

 

 

 

 

 

copied.

 

Toner

Manual/

3

 

"3" is slightly

smaller the

 

 

density is.

 

save

Photo

 

 

copied.

 

 

 

 

 

7 – 8

Page 38
Image 38
Sharp AR-160, AR-161 specifications Image density adjustment, Original sensor adjustment SIM, Copy mode SIM, Spf

AR-160, AR-161 specifications

The Sharp AR-161 and AR-160 are monochrome multifunction printers that have made a mark in the office equipment landscape with their impressive features, technologies, and characteristics. Both devices are designed to cater to the needs of small to medium-sized businesses that require reliable, efficient, and compact systems for their printing, copying, and scanning needs.

One of the main features of the Sharp AR-161 and AR-160 is their impressive speed. The AR-161 can produce up to 16 pages per minute (ppm), while the AR-160 offers a slightly lower output at 15 ppm. This makes both models suitable for environments where quick document turnaround is essential. Additionally, both machines have a warm-up time of approximately 20 seconds, ensuring minimal downtime when starting up.

In terms of paper handling, both models come equipped with a 250-sheet paper drawer and a 100-sheet bypass tray, allowing for a variety of media types and sizes. The automatic document feeder (ADF) can accommodate up to 50 sheets, making it easier to handle multi-page documents without manual intervention. This feature enhances workflow efficiency significantly, particularly in busy office settings.

The Sharp AR-161 and AR-160 utilize advanced copying technologies, including a high-resolution scanning capability of up to 600 x 600 dpi. This means that documents are reproduced with clarity and detail, making them suitable for professional presentations and reports. The devices also offer various copying options, such as zoom, collation, and reduction/enlargement, providing versatility for different copying tasks.

Both models are equipped with Sharp's innovative ImageSEND technology, which allows users to scan documents directly to email, network folders, or USB drives with ease. This feature enhances productivity by streamlining the scanning process, ensuring that documents can be shared quickly and efficiently.

Furthermore, energy efficiency is a hallmark of the Sharp AR-161 and AR-160, as both models are ENERGY STAR qualified. This means they are designed to use less energy, helping businesses reduce their environmental impact while also saving on operational costs.

In conclusion, the Sharp AR-161 and AR-160 combine speed, versatility, and energy efficiency in a sleek design. Their advanced copying technologies and smart features make them ideal choices for businesses seeking reliable multifunction devices that can enhance productivity without compromising on quality.