Sharp AR-5516S, AR-5520S 3, 4, 5

13

BEFORE USING THE MACHINE

1

3Use the [ORIGINAL] key () to

select the paper size.

The indicator of the

selected paper size lights

up.

Customise the bypass tray setting

• Enter a value for the horizontal/vertical direction by

pressing the numeric keys.

Press the [ ] key to switch the horizontal/vertical

direction.

The horizontal direction is selected:

zoom indicator lights up

The vertical direction is selected:

zoom indicator does not light up

When finished, press and hold [ ].

Available value

4Squeeze the lock lever of the front

guide and slide the front guide to

match the width of the paper, and

move the left guide to the appropriate

slot as marked on the tray.

• The front guide is a slide-type guide. Grasp the

locking knob on the guide and slide the guide to the

indicator line of the paper to be loaded.

• The left guide is an insert-type guide. Remove it and

then insert it at the indicator line of the paper to be

loaded.

• If the bypass tray is selected, set the paper guides to

the copy paper width.

5Press the [START] key ( ) and then

the [TRAY SETTING] key ( ).

To change the paper size

setting of another tray,

repeat steps 2 to 5 after

pressing the [START]

key ( ).

Important points when using the printer mode

Make sure that the tray's paper size setting is the

same as the tray's paper size setting in the printer

driver. For example, if the tray's paper size setting is

A4R, set "Set Paper Size" to "A4R". For more

information, see "CONFIGURING THE PRINTER

DRIVER" in the Start Guide.

Direction min. (mm) max. (mm)

horizontal 100 297

vertical 139 420

Affix the paper size label for the paper size

selected in step 3 to the label position on the

right end of the tray.

Left guide

Front guide

Note

Contents

Main Page CONTENTS 1 2 3 4 5 6 7 PERIPHERAL DEVICES AND SUPPLIES INTRODUCTION 1 BEFORE USING THE MACHINE PART NAMES AND FUNCTIONS Warning OPERATION PANEL Page POWER ON AND OFF POWER ON Turn the power switch to the "ON" position. POWER OFF Power save modes LOADING PAPER PAPER Special papers LOADING PAPER Loading the paper tray 1 until it stops. 2 1 paper width. 2 3 the way into the bypass tray. CHANGING A TRAY'S PAPER SIZE SETTING 1 ( ) for more than 5 seconds to set the selected paper size. 2 3 select the paper size. Customise the bypass tray setting 4 5 OPERATION IN COPY AND PRINTER MODES Chapter 2 COPY FUNCTIONS NORMAL COPYING Copying from the document glass 1 place the original. 1 been left on the document glass. Close the SPF. 2 of the original(s). 3 Auto paper select mode (when there are two or more paper trays) Removing the document cover Copying books or originals with folds or creases Originals that can be used in the SPF Originals that cannot be used in the SPF MAKING A COPY DARKER OR LIGHTER Original types 1 ( / / ) to select the original type. 2 REDUCTION/ENLARGEMENT/ZOOM AUTOMATIC RATIO SELECTION 1 feeder tray or on the document glass. If the original is placed on the document glass, select the original size. (p.15) MANUAL RATIO SELECTION 1 feeder tray or on the document glass. If the original is placed on the document glass, select the original size. (p.15) 3 SELECTING THE VERTICAL AND HORIZONTAL COPY RATIOS SEP ARATEL Y 1 2 3 4 6 7 8 TWO-SIDED COPYING USING THE BYPASS TRAY 3 1 2 4 DUAL PAGE COPYING 1 2 3 4 INTERRUPTING A COPY RUN (Interrupt Copying) 1 2 3 PRINTER FUNCTIONS BASIC PRINTING 1 on the operation panel is lit. 2 OPENING THE PRINTER DRIVER FROM THE "Start" BUTTON 1 "Control Panel" and then select "Printer". 2 driver icon. PRINTER DRIVER SETTING SCREEN SETTING ADVANCED PRINT FUNCTIONS PRINTING MULTIPLE PAGES ON ONE PAGE 3 (N-Up Printing) 1 FITTING THE PRINTED IMAGE TO THE PAPER (Fit To Paper Size) 3 1 2 ENLARGING/REDUCING THE PRINT IMAGE 1 ABCD ABCD 2 3 ADJUSTING THE BRIGHTNESS AND CONTRAST OF THE IMAGE 1 ADDING A WATERMARK TO PRINTED PAGES 2 SAVING FREQUENTLY USED PRINT SETTINGS SAVING SETTINGS AT THE TIME OF PRINTING (User Settings) 1 2 OUTLINE OF THE PRINT STATUS WINDOW Chapter 4 USER SETTINGS ADJUSTING THE AUTOMATIC EXPOSURE LEVEL 1 2 3 CUSTOMISING SETTINGS (System Settings) SYSTEM SETTINGS Page SELECTING A SETTING FOR A SYSTEM SETTING 1 the alarm indicators ( , , , , ) blink. 2 numeric keys. SETTINGS FOR AUDITING MODE AUDITING MODE AUDITING MODE SETTINGS SELECTING AUDITING MODE SETTINGS 1 2 3 4 Auditing mode (program No.10) Account number entry (program No.11) Account number change 1 with the numeric keys. 2 the copy. 3 TROUBLESHOOTING TROUBLESHOOTING MACHINE/COPYING PROBLEMS PRINTING PROBLEMS MACHINE/COPYING PROBLEMS Page Page PRINTING PROBLEMS Page INDICATORS AND DISPLAY MESSAGES MISFEED REMOVAL MISFEED IN THE SPF 1 Section A Section B MISFEED IN THE BYPASS TRAY 1 Gently pull the misfed paper out. 2 MISFEED IN THE MACHINE 1 A. Misfeed in the paper feed area 2 3 1 2 3 4 5 1 2 3 MISFEED IN THE UPPER PAPER TRAY 1 and remove the misfed paper. 2 3 MISFEED IN THE LOWER PAPER TRAY 5 1 2 3 REPLACING THE TONER CARTRIDGE 1 and open it. 2 pressing the lock release lever. ROUTINE MAINTENANCE CHECKING THE TOTAL OUTPUT COUNT AND TONER LEVEL CHECKING THE TOTAL OUTPUT COUNT [Total output count] Hold down the [0] key. CHECKING THE TONER LEVEL 1 3 ROUTINE MAINTENANCE CLEANING THE DOCUMENT GLASS AND SPF/DOCUMENT COVER cleaner. 2Clean the original scanning glass with CLEANING THE ORIGINAL SCANNING GLASS (ONLY WHEN AN SPF IS INSTALLED) 1 CLEANING THE BYPASS TRAY PAPER FEED ROLLER CLEANING THE TRANSFER CHARGER 7 1 2 3 4 7 PERIPHERAL DEVICES AND SUPPLIES PERIPHERAL DEVICES SINGLE PASS FEEDER Specifications 250-SHEET PAPER FEED UNIT/2 X 250-SHEET PAPER FEED UNIT Part names STORAGE OF SUPPLIES PROPER STORAGE Store the supplies in a location that is: Store paper in the wrapper and lying flat. GENUINE SUPPLIES