Manuals / Sharp / Computer Equipment / Projector

Sharp PG-D4010X specifications Connecting the Projector to a Computer

Models: PG-D4010X

1 34

Download 34 pages 37.76 Kb

Page 10

Setting up the Projector Network Environment

Setting up the Projector Network Environment

1.Connecting the Projector to a Computer

Establishing a one-to-one connection from the projector to a computer. Using a commercially available LAN cable (UTP cable, Category 5, cross-over type) you can conﬁgure the projector via the computer.

1 Disconnect the computer's LAN cable from the existing network.

A LAN cable being

connected to the network

2 Connect a commercially available LAN cable (UTP cable, Category 5, cross-over type) to the projector's LAN terminal and connect the other end of the cable to the computer's LAN terminal.

LAN cable

(cross-over type, commercially available)

3 Plug the power cord into the AC socket of the projector.

4 Turn on the computer.

Info

Conﬁ rm that the LINK LED on the rear of the projector illuminates. If the LINK LED does not illuminate, check the following:

•The LAN cable is properly connected.

•The power switches of both the projector and the computer are on.

ON

This completes the connection. Now proceed to “2. Setting an IP Address for the Computer”.

-10

Image 10

Sharp PG-D4010X specifications Connecting the Projector to a Computer, Setting up the Projector Network Environment

Contents

RS-232C Speciﬁcations and Commands SETUP MANUALConnecting Pin Assignments Setting up the Projector Using RS-232C orCOMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals mini Connecting Pin AssignmentsDVI-I Terminal 29 pin connector C3 C5 C4 C2 C1 8 7 2RS-232C Cable recommended connection D-sub 9 pin female connector Connecting Pin AssignmentsLAN Terminal LAN RJ-45 Communication conditions RS-232C Speciﬁcations and CommandsComputer control Basic formatExample When turning on the projector, make the following setting CommandsRS-232C Speciﬁcations and Commands P O W RRS-232C Speciﬁcations and Commands RS-232C Speciﬁcations and Commands RS-232C Speciﬁcations and Commands 3 The Lamp Timer Reset command is available only in standby mode2. Setting an IP address for the computer Setting up the Projector Network Environment1. Connecting the projector to a computer 3. Setting up a network connection for the projector1. Connecting the Projector to a Computer Setting up the Projector Network Environment2. Setting an IP Address for the Computer Setting up the Projector Network Environment7 After setting, click the “OK” button, and then restart the computer Setting up the Projector Network Environment6 Conﬁrm or change an IP address for the setup computer IP address Subnet mask Default gateway Do not input any values3. Setting up a Network Con- nection for the Projector Setting up the Projector Network EnvironmentSetting up the Projector Network Environment Click the “Apply” buttonControlling the Projector Using Internet Explorer Controlling the Projector via LANVersion 5.0 or later Controlling the Projector via LAN MAC Address Power Condition Lamp Timer Lamp Life Input Signal InfoPower Input Select Volume AV Mute Status StatusResolution Setting Projector Settings & AdjustmentsAuto Power Off Signal TypeMail - Originator Settings Making General Settings forSetting for Sending E-mail when an Error Occurs On this screen, you can make general settings relating to the networkMail - Recipient Settings Access URLSetting up the Projector Using RS-232C or Telnet When Connecting Using RS-232CWhen Connecting Using Telnet Setting up the Projector Using RS-232C or TelnetADVANCED SETUP MENU Setting up the Projector Using RS-232C or TelnetSETUP MENU 3 Default GatewaySETUP MENU Setting up the Projector Using RS-232C or TelnetVView All Setting SETUP MENUSETUP MENU Setting up the Projector Using RS-232C or TelnetSETUP MENU SSave & Quit1IP Address Setting up the Projector Using RS-232C or Telnet3Default Gateway 2Subnet Mask2 Enter password and press the “Enter” key. Display set password Setting up the Projector Using RS-232C or Telnet5Password 7Projector Nametions DDisconnect All Setting up the Projector Using RS-232C or TelnetAAdvanced Setup ADVANCED1Auto Logout TimeCarrying out Network Ping Test Setting of Accept IP Ad- dressSetting up the Projector Using RS-232C or Telnet Accepting All IP AddressesADVANCED0Search Port Setting up the Projector Using RS-232C or TelnetADVANCED!Restore Default Setting ADVANCEDQReturn to Main MenuResetting the Lamp Timer of the Projector via LAN Resetting the Lamp Timer of the Projector via LAN Troubleshooting Communication cannot be established with the projectorTroubleshooting Troubleshooting