R-1500

R-1501

R-1505

R-1506

TEST PROCEDURES

PROCEDURE

LETTER

COMPONENT TEST

6.Reinstall the outer case (cabinet).

7.Reconnect the power supply cord after the outer case is installed.

8.Run the oven and check all functions.

CAUTION: IF THE THERMAL CUT-OUT OR TEMPERATURE FUSE INDICATES AN OPEN CIRCUIT AT ROOM TEMPERATURE, REPLACE THERMAL CUT-OUT OR TEMPERATURE FUSE.

FPRIMARY INTERLOCK SWITCH TEST

1.Disconnect the power supply cord, and then remove outer case.

2.Open the door and block it open.

3.Discharge high voltage capacitor.

4.Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal of the switch. The meter should indicate an open circuit with the door open and a closed circuit with the door closed. If improper operation is indicated, replace the secondary interlock switch.

5.Reconnect all leads removed from components during testing.

6.Reinstall the outer case (cabinet).

7.Reconnect the power supply cord after the outer case is installed.

8.Run the oven and check all functions.

GSECONDARY INTERLOCK SYSTEM TEST DOOR SENSING SWITCH

1.Disconnect the power supply cord, and then remove outer case.

2.Open the door and block it open.

3.Discharge high voltage capacitor.

4.Isolate the switch and connect the ohmmeter to the common (COM.) and normally open (NO) terminal of the switch. The meter should indicate an open circuit with the door open and a closed circuit with the door closed. If improper operation is indicated, replace the door sensing switch.

5.Reconnect all leads removed from components during testing.

6.Reinstall the outer case (cabinet).

7.Reconnect the power supply cord after the outer case is installed.

8.Run the oven and check all functions.

NOTE: If the door sensing switch contacts fail in the open position and the door is closed, the cooling fan motor, stirrer motor and oven light will be activated by RY1.

SECONDARY INTERLOCK RELAY (RY2)

1.Disconnect the power supply cord, and then remove outer case.

2.Open the door and block it open.

3.Discharge high voltage capacitor.

4.Disconnect two (2) wire leads from the male tab terminals of the Secondary Interlock Relay. Check the state of the relay contacts using a ohmmeter. The relay contacts should be open. If the relay contacts are closed, replace the circuit board entirely or the relay itself.

5.Reconnect all leads removed from components during testing.

6.Reinstall the outer case (cabinet).

7.Reconnect the power supply cord after the outer case is installed.

8.Run the oven and check all functions.

HMONITOR SWITCH TEST

1.Disconnect the power supply cord, and then remove outer case.

2.Open the door and block it open.

3.Discharge high voltage capacitor.

4.Before performing this test, make sure that the primary interlock switch and the secondary interlock relay are operating properly, according to the above Switch and Interlock system Test Procedures. Disconnect the wire lead from the monitor switch (COM) terminal. Check the monitor switch operation by using the ohmmeter as follows. When the door is open, the meter should indicate a closed circuit. When the monitor switch actuator is pushed by a screw driver through the lower latch hole on the front

15

Page 17
Image 17
Sharp R-1505 Primary Interlock Switch Test, Secondary Interlock System Test Door Sensing Switch, Monitor Switch Test

R-1506, R-1501, R-1505, R-1500 specifications

The Sharp R-1500, R-1505, R-1501, and R-1506 are part of Sharp's extensive line of microwave ovens, showcasing advanced cooking technologies and user-friendly features that cater to the modern kitchen. These models are designed to provide convenience and efficiency while delivering consistent cooking results.

One of the standout features across these models is the use of Sharp's innovative microwave technology, which ensures even heating and cooking. This is achieved through a combination of advanced microwave distribution systems that help to minimize cold spots common in traditional microwaves. As a result, users can enjoy perfectly cooked meals, whether it's reheating leftovers or preparing a fresh dish.

Each model comes equipped with a variety of cooking presets that simplify meal preparation. These presets are tailored for a range of foods, including popcorn, pizza, vegetables, and baked goods. With just the press of a button, users can automatically adjust the cooking time and power level, making the cooking process intuitive and hassle-free.

The R-1500 and R-1505 models, in particular, offer a sleek and modern design that can seamlessly blend into any kitchen décor. The front-facing control panel is easy to read and navigate, while the spacious interior can accommodate larger dishes, making these models ideal for family meals or entertaining guests.

In addition to their cooking capabilities, these microwaves prioritize energy efficiency and safety. With features like a child lock function and an eco-mode, users can have peace of mind knowing that their appliance is safe for the entire family and environmentally conscious.

The R-1501 model adds additional versatility by including a grill function, allowing users to achieve that perfect crispiness on meats and vegetables. This feature enhances the range of cooking options available, making it suitable for those who enjoy grilling but may not have the outdoor space or equipment.

Lastly, the R-1506 combines the benefits of microwave cooking with user-friendly features such as a digital display and programmable timers. This model is particularly well-suited for busy households, as it allows for quick meal prep without sacrificing quality.

In summary, the Sharp R-1500, R-1505, R-1501, and R-1506 microwave ovens represent a blend of advanced technology, safety features, and user-convenience. They cater to a broad spectrum of cooking needs, from basic reheating to more complex meal preparations, all while maintaining a focus on efficiency and style.