R - 5 3 0 E K

R - 530EW

13.Now, door panel is free.

14.Slide latch head upward and remove it from door frame by releasing latch spring from door frame and latch head.

15.Now, latch head and latch spring are free. 16.Remove one (1) screw holding the door glass stopper to

the door frame.

17.Remove door glass stopper from door frame.

18.Slide the door glass rightwards and then slide upwards to release the door glass from the tabs holding it.

19.Remove the door glass from the door frame. 20.Now, door frame is free.

REINSTALLATION

1. Re-install door glass to door frame as follows.

1-1. Insert the upper edge of the door glass into the five (5) tabs of the door frame.

1-2. Slide the door glass downwards and insert the lower edge of door glass into the five (5) tabs of the door frame.

1-3. Slide the door glass leftwards and insert the left edge of door glass into the two (2) tabs of the door frame.

2.Re-install the door glass stopper to the door frame so that the two (2) holes of the door glass stopper fit to the two (2) pins of the door frame. And hold the door glass stopper with one (1) screw.

3.Re-install the latch spring to the latch head. Re-install the latch spring to the door frame. Re-install latch head to door frame.

4.Re-install door panel to door frame by catching ten (10) tabs of door frame on the edges of door panel.

5.Put sealer film on door panel. Refer to “Sealer Film” about how to handle new one.

6.Catch two (2) pins of door panel on two (2) hole of upper and lower oven hinges.

7.Re-install choke cover to door panel by pushing.

Note: After any service to the door;

(A)Make sure that door sensing switch and secondary interlock switch are operating properly. (Refer to chapter “Test Procedures”.).

(B)An approved microwave survey meter should be

used to assure compliance with proper microwave radiation emission limitation standards.

After any service, make sure of the following :

1.Door latch heads smoothly catch latch hook through latch holes and that latch head goes through center of latch hole.

2.Deviation of door alignment from horizontal line of cavity face plate is to be less than 1.0mm.

3.Door is positioned with its face pressed toward cavity face plate.

4.Check for microwave leakage around door with an approved microwave survey meter. (Refer to Microwave Measurement Procedure.)

Note: The door on a microwave oven is designed to act as an electronic seal preventing the leakage of microwave energy from oven cavity during cook cycle. This function does not require that door be air- tight, moisture (condensation)-tight or light-tight. Therefore, occasional appearance of moisture, light or sensing of gentle warm air movement around oven door is not abnormal and do not of themselves indicate a leakage of microwave energy from oven cavity.

Pin

 

Upper

Upper Oven

Hinge

Oven Hinge

 

Slit Choke

Lower

Oven Hinge

Lower Oven

Hinge

Pin

Choke Cover

Figure C-5. Door Replacement

SEALER FILM

Installation

1.Put the adhesive tape on the backing film of the sealer film as shown in Fig. C-6.

2.Tear the backing film by pulling the adhesive tape.

3.Put the pasted side of the sealer film on the door panel

Sealer film

Backing film

Adhesive tape

Figure C-6. Sealer film

32

Page 34
Image 34
Sharp R-530EK service manual Sealer Film, Reinstallation, After any service, make sure of the following, Installation

R-530EK specifications

The Sharp R-530EK is a notable microwave oven that combines functionality with innovation to enhance cooking convenience. With a sleek design and user-friendly interface, this model has earned a place in many kitchens around the globe.

One of the primary features of the Sharp R-530EK is its powerful microwave output. The oven boasts a maximum power of 900 watts, ensuring that food can be heated quickly and evenly. This power level allows users to prepare a variety of meals, from reheating leftovers to cooking dishes from scratch, in significantly less time than traditional cooking methods.

The R-530EK is equipped with a spacious interior, offering 25 liters of capacity. This ample space allows for cooking larger dishes or multiple servings at once. The turntable design ensures even cooking by rotating food during the heating process, further enhancing the microwave's efficiency.

Another standout feature of the Sharp R-530EK is its array of pre-programmed auto-cook menus. These presets simplify cooking by providing specific times and power levels for various types of food, including popcorn, pizzas, and oatmeal. Users can simply select the appropriate setting, and the microwave takes care of the rest, making it ideal for those who may not have extensive cooking experience.

The microwave utilizes advanced inverter technology, a feature that sets it apart from many conventional microwave ovens. Inverter technology allows for continuous and consistent power output, providing more precise temperature control. This means that delicate foods such as seafood or chocolate can be heated without the risk of overcooking or burning, resulting in better texture and flavor.

Additionally, the R-530EK is designed with multiple cooking functions that enhance its versatility. These include defrosting capabilities, grilling options, and even signals indicating the completion of cooking cycles. The easy-to-read digital display and intuitively designed buttons contribute to the overall user experience, making it accessible for individuals of all ages.

Moreover, this microwave oven ensures safety with features such as a child lock, which prevents accidental operation by little hands. The Sharp R-530EK is both an efficient and reliable addition to any kitchen, embodying the perfect blend of cutting-edge technology and practical design to meet the demands of modern cooking. With its impressive range of features and performance capabilities, it stands as a valuable tool for aspiring chefs and busy families alike.