BASIC OPERATION
HOW TO SET A DELAYED RECORDING
7.Enter the start time using the [
/
] or NUMBER BUTTONS, hours first then
minutes (when entering less than 10 hours or minutes add a '0' before the number), for
example for 21:05 start, press 2 1 0 5.
Then press 
to move to the next setting.
8.Enter the stop time, for example for 22:30 stop, press 2 2 3 0.
9.If you wish to change the RECORDING
SPEED, use the [
/
] to highlight SP. Press [
/
]to select standard play (SP), long play (LP) or extended play (EP) as required.
10.[See note below]. For VPS/PDC setting use the
[
/
] to highlight the final column. Using the [
/
] will select VPS/PDC ON or OFF (✱ = ON - = OFF).
11.Press the SET SET button to confirm.
•The MENU now shows all the timer settings you have entered. If you wish to make additional timer recordings, repeat this procedure.
12.When you have completed entering timer
settings, press the MENU 
button to remove the menu from the TV screen.
13.Ensure that the tape on which you wish to record is inserted into the VCR, then press the
TIMER ON/OFF 
button once to place
the VCR in TIMER STANDBY mode. 
will be shown on the display.
7.
1 / 2
DA T E P R S T AR T | S T OP |
2 1 / 0 6 0 2 1 2 : 0 0 | 1 3 : 0 0 S P * |
| 9 / 0 7 D 0 3 2 1 : 0 5 | ||||||||||||||
- | - | / | - | - | - | - | - | : - | - | - | : - | - | - | - | - |
- | - | / | - | - | - | - | - | : - | - | - | : - | - | - | - | - |
9.
1 / 2
DA T E P R S T AR T | S T OP |
2 1 / 0 6 0 2 1 2 : 0 0 | 1 3 : 0 0 S P * |
9 / 0 7 D 0 3 2 1 : 0 5 2 2 : 3 0 L P -
- | - | / | - | - | - | - | - | : | - | - | - | : | - | - | - | - | - |
- | - | / | - | - | - | - | - | : | - | - | - | : | - | - | - | - | - |
10.
DA T E P R S T AR T S T OP | 1 / 2 | |||
| ||||
2 1 / 0 6 0 2 | 1 2 : 0 0 | 1 3 : 0 0 S P * | ||
9 / 0 7 D 0 3 | 2 1 : 0 5 | 2 2 : 3 0 L P - | ||
- | - - | - - - | ||
- | - - | - - - | ||
NOTES:
•VPS/PDC is a signal broadcast by some TV stations which adjusts the start and stop time of your VCR recording. This ensures that if there is a change in broadcast time for your programme the VCR will still record the whole programme. It is essential that the start time as it appears in the TV listing is used to program the VCR, as this information is used to identify the VPS/PDC signal corresponding to your programme.
•If the 
symbol flashes a video tape has not been inserted into the VCR.
•If the video tape is ejected when the VCR tries to record the record protection tab has been removed.
•During recording, press STOP 
to cancel the recording. If there are further recordings to be made, the VCR will return to Timer Standby.
www.sharp.co.uk/support
20
