TINS-A082UMN1.book Page 47 Monday, November 4, 2002 2:33 PM

MORE INFORMATION ABOUT YOUR VCR

TROUBLESHOOTING

BEFORE REQUESTING SERVICE!

The following conditions do not always denote trouble. Therefore, perform the checks described below before calling for service. If the problem cannot be corrected by the use of this guide, remove the mains plugs from the wall socket and contact the dealer or supplier from whom the unit was purchased in order to obtain service. Where this is not possible, please contact the telephone number listed below, you will then be given details of how to obtain service.

Tel. 08705 274277 (office hours) or (01) 676 0648 if telephoning from Ireland- Please note: All calls will be charged at local rate.

 

AREA

PROBLEM

 

POSSIBLE CAUSE/CURE

 

INSTALLATION

TV will not tune in to

Check all the cables are correctly

 

 

 

 

 

the VCR.

 

connected.

 

 

 

 

 

 

 

 

 

 

 

 

Check your TV manual for correct tuning of

 

 

 

 

 

 

 

your TV.

 

 

 

 

 

 

 

 

 

 

 

 

 

Auto Installation

Reset the VCR and complete AUTO

 

 

 

 

 

screen does not

 

INSTALLATION again. (Refer to VCR Reset at

 

 

 

 

 

appear when the VCR

 

the back of the book.)

 

 

 

 

 

is switched on OR Auto

 

 

 

 

 

 

 

Installation is not

 

 

 

 

 

 

 

complete.

 

 

 

 

 

 

 

 

 

 

POWER

Display is not working.

Make sure the power cord is plugged in.

 

 

 

 

 

 

Make sure the wall socket has power (check

 

 

 

 

 

 

 

 

 

 

 

 

 

by plugging another appliance in).

 

 

 

 

VCR will not operate -

Press the TIMER ON/OFF

 

 

 

button to

 

 

 

 

 

appears in VCR

 

 

 

 

 

 

 

 

 

disengage timer.

 

 

 

 

 

 

 

 

 

display.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VCR will not respond to

Check the CHILD LOCK is not engaged.

 

 

 

 

any commands.

Safety device operating: unplug VCR for 2

 

 

 

 

 

 

 

hours.

 

 

 

 

 

 

 

 

 

 

 

 

 

PLAYBACK No picture appears.

Make sure the TV is set to the video channel.

 

 

 

 

 

 

Check all connecting cables.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Playback picture is

Adjust the tracking using the

 

 

 

 

snowy.

 

VCR CHANNEL

/

 

 

buttons.

Try another tape.

The video heads may have been contaminated - refer to a SHARP Service Facility.

 

 

Playback/Recording

• Ensure the VCR is connected to a stereo TV

 

 

does not play back in

with a SCART lead.

 

 

Stereo

 

 

 

 

 

• Programme may not carry stereo.

 

 

 

 

 

 

 

 

RECORDING Tape is automatically

• The record-protection tab has been

 

 

ejected when

pressing

removed from the cassette.

 

 

 

 

the REC

 

or

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIMER ON/OFF

 

 

 

 

 

 

buttons.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

www.sharp.co.uk/support

47

Page 49
Image 49
Sharp VC-MH835HM Troubleshooting, Before Requesting Service, Area Problem Possible CAUSE/CURE, Timer ON/OFF