Remaining Recording Time Display

When the VIEWCAM is recording in Camera mode, about 10 minutes before the tape reaches the end, an on-screen indicator displays the approximate remaining recording time.

DISPLAY button

Approx. remaining

On-screen

recording time

indicator

10 min.–8 min.

T A P E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

8 min.–6 min.

T A P E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6 min.–4 min.

T A P E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

4 min.–2 min.

T A P E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2 min.–1 min.

T A P E

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1 min.–0 min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

0 min.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(The tape has

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

reached the end.)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

To turn off the remaining recording time display, press the DISPLAY button.

Notes:

The remaining recording time displays only show the approximate time left. Also, they vary slightly depending on the length of tape used. (This function’s design is based on the P6-120 tape standard.)

If you turn off the remaining recording time display, it will reappear after a short interval to indicate the new time remaining.

The remaining recording time display appears 5 seconds after pressing the REC START/ STOP button to begin recording.

Remaining Battery Power

Display

When using the VIEWCAM with the battery pack as the power source, you can turn on and off the remaining battery power display by pressing the DISPLAY button.

If the battery power becomes very low, a warning indicator will appear. Replace the battery pack.

CameraRecording

BasicOperations

DISPLAY button

(Green)

 

 

(Green)

Remaining battery

power display

(Red)

 

 

 

 

Warning indicator

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes:

Use the remaining battery power display only as an approximate indication.

The battery power display may change to either a higher or lower level if you set the Power switch to OFF and then back to CAMERA or VCR.

In cold environments, the red remaining battery power display may appear sooner. The battery pack, however, can be used until the warning indicator appears. Replace the battery pack at this time.

Battery consumption may vary depending on the condition of use.

Use of the zoom function when the warning indicator is displayed may cause the VIEWCAM to suddenly lose power.

20

Page 29
Image 29
Sharp VL-A110U operation manual Remaining Recording Time Display, Remaining Battery Power Display