Sharp XL-HF200P(BK) Maintenance, Specifications, E-15, Troubleshooting chart continued,  Amplifier

Troubleshooting chart (continued)

Care of compact discs

Compact discs are fairly resistant to damage, however mistracking can occur due to an accumulation of dirt on the disc surface. Follow the guidelines below for maximum enjoyment from your CD collection and player.

 Do not write on either side of the disc, particularly the non-label side from which signals are read. Do not mark this surface.

 Keep your discs away from direct sunlight, heat, and excessive moisture.

 Always hold the CDs by the edges. Fingerprints, dirt, or water on the CDs can cause noise or mistracking. If a CD is dirty or does not play properly, clean it with a soft, dry cloth, wiping straight out from the center, along the radius.

Maintenance

Cleaning the CD pickup lens

In order to ensure proper operation of the CD player, preventative maintenance (cleaning of the laser pickup lens) should be performed periodically. Lens cleaners are commercially available. Contact your local CD software dealer

for options.

Cleaning the cabinet

Periodically wipe the cabinet with a soft cloth and a diluted soap solution, then with a dry cloth.

Caution:

 Do not use chemicals for cleaning (gasoline, paint thinner, etc.). It may damage the cabinet.

 Do not apply oil to the inside of the unit. It may cause malfunctions.

Specifications

As part of our policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

General

Power source	AC 120 V ~ 60 Hz
Power consumption	40 W
Dimensions	Width: 8 - 1/2” (215 mm)
	Height: 3 - 1/2” (90 mm)
	Depth: 11 - 4/5” (300 mm)
Weight	8.8 lbs. (4.0 kg)

 CD player

Type	Single disc multi-play compact disc player
Signal readout	Non-contact, 3-beam
	semiconductor laser pickup
D/A converter	Multi bit D/A converter
Frequency response	20 - 20,000 Hz
Dynamic range	90 dB (1 kHz)

 Amplifier

Output power	RMS:	Total 100 watt (50 W per channel
		into 4 ohms at 1 kHz, 10% Total
		harmonic distortion.)
	FTC:	37.5 watt minimum RMS per
		channel into 4 ohms from 100 Hz
		to 20 kHz, 10% Total harmonic
		distortion.
Output terminals	Speakers: 4 ohms
	20Hz - 20kHz
	Subwoofer Pre-out (audio signal):
	200 mV/10 k ohms at 70 Hz
	Video output: 1 Vp-p
	Headphones: 16-50 ohms
	(recommended: 32 ohms)
Input terminals	Audio In (audio signal):
	500 mV/47 k ohms
	Line in (Analog input):
	500 mV/47 k ohms

 USB

USB host interface	 Complies with USB 1.1 (Full
	Speed)/2.0 Mass Storage Class.
	 Support Bulk only and CBI protocol.
Support file	 MPEG 1 Layer 3
	 WMA (Non DRM)
Bitrate support	 MP3 (32 ~ 320 kbps)
	 WMA (64 ~ 160 kbps)
Other	 Maximum total number of MP3/WMA
	files is 1024.
	 Maximum total number of folders is
	255 INCLUSIVE of root directory.
	 The ID3TAG information supported
	are TITLE, ARTIST and ALBUM
	only.
	 Supports ID3TAG version 1 and
	version 2.
File system support	 Support USB devices with Microsoft
	Windows/DOS/FAT 12/FAT 16/ FAT
	32.
	 2 kbyte block length for sector.

 Tuner

Frequency range	FM: 87.5 - 108 MHz
	AM: 530 - 1,710 kHz
Preset	40 (FM and AM station)

 Speaker

Type	2-way type speaker system
	1” (2.5 cm) Dome-Tweeter
	4-3/4” (12 cm) woofer
Maximum input power	100 W
Rated input power	50 W
Impedance	4 ohms
Dimensions	Width: 5 - 13/16” (148 mm)
	Height: 10-1/4” (260 mm)
	Depth: 8” (203.5 mm)
Weight	5.4 lbs. (2.5 kg)/each

E-15