Sharp XL-HF200P(BK) operation manual IMPORTANT SAFETY INSTRUCTIONS continued

IMPORTANT SAFETY INSTRUCTIONS (continued)

11)Only use attachments/accessories specified by the manufacturer.

12)Use only with the cart, stand, tripod,

bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13)Unplug this apparatus during lightning storms or when unused for long periods of time.

14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Additional Safety Information

15)	Power Sources - This product should be operated
	only from the type of power source indicated on the
	marking label. If you are not sure of the type of power
	supply to your home, consult your product dealer or
	local power company. For product intended to operate
	from battery power, or other sources, refer to the
	operating instructions.
16)	Overloading - Do not overload wall outlets, extension
	cords, or integral convenience receptacles as this can

20)Safety Check - Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21)Wall or ceiling mounting - When mounting the product on a wall or ceiling, be sure to install the product according to the method recommended by the manufacturer.

22)Power Lines - An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

23)Outdoor Antenna Grounding - If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article810 of the National Electrical Code, ANSI/NFPA 70, provides information with regards to proper grounding of the mast and supporting structure, grounding of the cord-in wire to an antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

	result in a risk of fire or electric shock.
17)	Object and Liquid Entry - Never push objects of any
	kind into this product through openings as they may
	touch dangerous voltage points or short-out parts that
	could result in a fire or electric shock. Never spill liquid
	of any kind on the product.
18)	Damage Requiring Service - Unplug this product from
	the wall outlet and refer servicing to qualified service
	personnel under the following conditions:
	a) When the AC cord or plug is damaged,
	b) If liquid has been spilled, or objects have fallen

Example of antenna grounding asper National Electrical Code, ANSI/NFPA 70

GROUND

CLAMP

ELECTRIC

SERVICE

EQUIPMENT

NEC - NATIONAL ELECTRICAL CODE S2898A

ANTENNA CORD IN WIRE

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING

ELECTRODE SYSTEM

(NEC ART250, PARTH)

	into the product,
c)	If the product has been exposed to rain or water,
d)	If the product does not operate normally by
	following the operating instructions. Adjust only
	those controls that are covered by the operating
	instructions as an improper adjustment of other
	controls may result in damage and will often
	require extensive work by a qualified technician to
	restore the product to its normal operation,
e)	If the product has been dropped or damaged in
	any way, and
f)	When the product exhibits a distinct change in
	performance - this indicates a need for service.
19) Replacement Parts - When replacement parts are
required, be sure the service technician has used
replacement parts specified by the manufacturer or
have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric
shock, or other hazards.

24)Protective Attachment Plug - The product is equipped with an attachment plug having overload protection. This is a safety feature. See Instruction Manual

for replacement or resetting of protective device. If replacement of the plug is required, be sure the service technician has used a replacement plug specified by the manufacturer that has the same overload protection as the original plug.

25)Stand - Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

E-2