Sharp XL-HF200P(BK) Timer and sleep operation Remote control only, E-12, Timer playback

Setting the clock (continued)

5To adjust the hour, press the or button and then press the ENTER button. Press the or button once to advance the time by 1 hour. Hold it down to advance continuously.

6To adjust the minutes, press the or button and then press the ENTER button. Press the or button once to advance the time by 1 minute.

To confirm the time display:

Press the CLOCK/TIMER button. The time display will appear for about 5 seconds.

Note:

When power supply is restored after unit is plugged in again or after a power failure, reset the clock (pages 11).

To readjust the clock:

Perform “Setting the clock” from step 1. If the “Clock” does not appear in step 2, step 4 (for selecting the 24-hour or 12-hour display) will be skipped.

To change the 24-hour or 12-hour display:

1Clear all the programed contents. [Refer to “Factory reset, clearing all memory” on page 14 for details.]

2Perform “Setting the clock” from step 1 onwards.

Timer and sleep operation (Remote control only)

Once timer:

Once timer play works for one time only at a preset time.

(“” indicator).

Daily timer:

Daily timer play works at the same preset time every day that we set. For example, set the timer as a wake-up call every morning.

(“DAILY” indicator).

Using the once timer and daily timer in combination:

For example, use the once timer to listen a radio program, and use the daily timer to wake up.

	1 minute or more
Daily timer			Once timer
Start	Stop	Start	Stop

Timer playback

Before setting timer:

 Check that the clock is set to the correct time (refer to page 11-12). If it is not set, you cannot use the timer function.

 For timer playback: Plug in USB or load discs or dock iPod to be played.

1Press the ON/STAND-BY button to turn the power on.

2Press and hold the CLOCK/TIMER button.

3Within 10 seconds, press the or button to select “Once” or “Daily”, and press the ENTER button.

4Within 10 seconds, press the or button to select “Timer Set”, and press the ENTER button.

5To select the timer playback source (CD, TUNER, USB, iPod,

AUDIO IN, LINE IN), press the or button. Press the ENTER button.

When you select the tuner, select a station by pressing the or button, and then press the ENTER button. If a station has not been programed, “No Preset” will be displayed and timer setting will be canceled.

6To adjust the day, press the or button and then press the ENTER button.

7Press the ENTER button to adjust the hour. Press the or button and then press the ENTER button.

8To adjust the minutes, press the or button and then press the ENTER button.

9Set the time to finish as in steps 7 and 8 above.

10Adjust the volume using the VOLUME control, and then press the ENTER button. Do not turn the volume up too high.

11Press the ON/STAND-BY button to enter the power stand-by mode. The “TIMER” indicator lights up and the unit is ready for timer playback.

12 When the preset time is reached, playback will start. The volume will increase gradually until it reaches the preset volume. The timer indicator will blink during timer playback.

13When the timer end time is reached, the system will enter the power stand-by mode automatically.

Once timer:

The timer will be canceled.

Daily timer:

The timer operates at the same time every day. It will continue until the daily timer setting is canceled. Cancel the daily timer when it is not in use.

Notes:

 When performing timer playback using another unit connected to the USB terminal or AUDIO IN jack, select “USB” or “AUDIO IN” or “LINE IN” in step 5.

 This unit will turn on or enter the power stand-by mode automatically. However, the connected unit will not turn on or off. To stop the timer playback, follow step “Canceling the timer setting” of this page.

Checking the timer setting:

1Turn the power on and press and hold down the CLOCK/ TIMER button.

2Within 10 seconds, press the or button to select “Once” or “Daily”, and press the ENTER button.

3Within 10 seconds, press the or button to select “Timer Call”, and press the ENTER button.

Canceling the timer setting:

1Turn the power on and press and hold down the CLOCK/ TIMER button.

2Within 10 seconds, press the or button to select “Once” or “Daily”, and press the ENTER button.

3Within 10 seconds, press the or button to select “Timer Off”, and press the ENTER button. Timer will be canceled (the setting will not be canceled).

Reusing the memorized timer setting:

The timer setting will be memorized once it is entered. To reuse the same setting, perform the following operations.

1Turn the power on and press and hold down the CLOCK/ TIMER button.

2Within 10 seconds, press the or button to select “Once” or “Daily”, and press the ENTER button.

3Within 10 seconds, press the or button to select “Timer On” , and press the ENTER button.

4Press the ON/STAND-BY button to enter the power stand- by mode.

E-12