ENGLISH
SETTING THE SPEAKER SETUP
•After you have installed this unit and connected all the components, you first perform the speaker setup settings for the optimum sound acoustics according to your environment and speaker layout.
•Even when you change speakers, speaker positions, or the layout of your listening environment, you should perform the speaker setup settings, too.
•When performing the AUTO SPEAKER SETUP procedure, you need not perform the SPEAKER CONFIGURATION, SPEAKER DISTANCE and CH LEVEL SETUP procedures.
S P E A KE R S E T U P
S P E A K E R C O N F I G U R A T I O N 
S P E A K E R D I S T A N C E 
V I R T U A L S P E A K E R S E T U P 
S U B W O O F E R : A C T I V E 
S U B W O O F E R M O D E : L F E 
C R O S S O V E R F R E Q . : 8 0 H z 
A U T O S P E A K E R S E T U P 
, 
: M o v e
R E T U R N : B a c k E N T E R : S e l e c t
To select the sizes of the speakers that are connected.
To enter the distance between the listening position and each speaker to set the delay time automatically for the optimum surround playback.
To adjust the Dolby Virtual Speaker setting modes as desired.
To select the type of the subwoofer that is connected.
To select the desired subwoofer mode
To select the desired crossover frequency.
To set the speaker setup and channel level setup automatically.
When selecting the SPEAKER CONFIGURATION
Press the CURSOR UP(
)/DOWN( 
) buttons to select the SPEAKER CONFIGURATION, then press
1 | the ENTER button. |
|
| ||
|
|
| S P E A K E R CO N F I G UR A T I O N | ||
|
|
| S U B W O O F E R : | Yes | |
| PAGE | MAIN | F R O N T | : | Large |
| VOL |
| C E N T E R | : | Large |
|
|
| S U R R R O U N D : | Large | |
|
|
| S / B C H | : | 2CH |
| 1 |
| S U R R . B A C K : | Large | |
| 2 | 3 |
|
| |
| 4 | 5 | 6 |
|
|
| 7 | 8 | 9 | , : S e l e c t | |
|
| 0 | R E T U R N : B a c k | ||
| MI | M2 | M3 |
|
|
Press the CURSOR UP( )/DOWN( ) buttons to select the desired speaker.
2
PAGE | MAIN | • Each time these buttons are pressed, “ ” and “ ” are |
VOL |
| |
|
| moved to the corresponding speaker mode. |
1 | 2 | 3 |
4 | 5 | 6 |
7 | 8 | 9 |
| 0 |
|
MI | M2 | M3 |
Press the CURSOR LEFT( )/RIGHT( ) buttons to select the desired mode.
3 | • Depending on your speaker type, you can select one of these following speaker types. |
|
•Yes/No : Select the desired depending on whether a subwoofer is connected or not.
•Large : Select this when connecting speakers that can fully reproduce sounds below crossover frequency.
PAGE | MAIN |
| • Small : Select this when connecting speakers that cannot fully reproduce sounds below |
VOL |
|
| |
|
|
| crossover frequency.When this is selected, sounds below crossover frequency are |
|
|
| sent to the subwoofer. |
1 | 2 | 3 | • None : Select this when no speakers are connected. When this is selected, sounds are sent |
4 | 5 | 6 | to the speakers which are not set to None. |
7 | 0 | 9 | |
8 | • 2CH/1CH : Select the desired depending on the number of surround back speakers. | ||
MI | M2 | M3 |
Notes :
•When speakers are set to “Small”, you should set the CROSSOVER FREQUENCY correctly according to their low frequency playback capacity. (Refer to “When selecting the CROSSOVER FREQUENCY” on page 48.)
•When “FRONT’ is set to “Small”, “SUBWOOFER” is automatically set to “Yes”, and when “SUBWOOFER” is set to “No”, “FRONT” is automatically set to “Large”.
•When “FRONT” is set to “Small”, “CENTER”, “SURROUND” and “SURR. BACK” cannot be set to “Large”.
•When “SURROUND” is set to “None”, “S/B CH” is automatically set to “None”.
44
