Installing a Trimmer Head, Gear Case Shaft | Shindaiwa 81704

Installing a Trimmer Head

NOTE:

The C2510 is shipped with Holder A, the blade retainer (safety clip), Holder B, shaft bolt, and bolt guard installed. The shaft bolt is a LEFT-HAND thread. Remove it by turning

CLOCKWISE!

1.With the gear case output shaft facing up, rotate the gearshaft and holder A until the hole in holder A aligns with the matching hole in the gear case flange, and then lock the holder to the gear by inserting the long end of the hex wrench through both holes. See Figure 10.

2.Using the combination spark plug/ screwdriver wrench, remove the shaft bolt and bolt guard. See Figure 10.

NOTE:

Shaft Bolt (not

used)

Gear Case

Shaft

Bolt Guard (not

used)

Holder B

Holder A

Figure 10

Hand-tighten Trimmer Head (counter-

clockwise to install)

Hex Wrench

Figure 11

Make sure holder B is installed on the gear- case with the splined hole engaging the gear-case shaft.

3.Using the hex wrench to secure Holder A , install and hand-tighten the trim- mer head (counter-clockwise to install). See Figure 11.

5.Remove the hex wrench from the gear case and holder.

The C2510 should now be completely assembled to operate as a trimmer.

Image 8

Shindaiwa 81704 manual Installing a Trimmer Head, Gear Case Shaft

Contents

C2510 Brushcutter C2510 Introduction ContentsSafety Instructions Properly Equipped Operator Always use the proper cutting tool for the job Safety Labels Be Aware of the Working Environment Product Description Specifications C2510Prior to Assembly Assembly Install the Cutting Attachment Shield C2510Cutting Attachment Shield Sub-Shield C2510 Adjustments Handle Bar C2510 Install the handlebarAdjust Throttle Lever Free Play Reinstall the air cleaner cover Installing a Trimmer Head Gear Case Shaft Installing a Blade Remove the hex wrench Mixing Fuel Filling the Fuel TankStarting the Engine Examples of 501 mixing quantities Adjusting Engine Idle When the Engine StartsIdle Speed Adjustment Stopping the Engine Cutting Grass-Units equipped with a trimmer head Checking Unit ConditionShoulder Strap C2510 Using a Blade C2510 Operating Units with a Blade Hour Maintenance General MaintenanceDaily Maintenance 10/15-Hour Maintenance Every 10 to 15 hours of operation 139/150-Hour Maintenance Spark Arrester Screen Maintenance Long Term Storage Blade SharpeningShindaiwa Tornado Blade Multiple-tooth Circular Blade Troubleshooting Guide Engine does not Start Additional Problems Manufacturers Warranty Coverage Garantía DE Servicio DE Solicitudes Continuación Diagnostico Guia Adicionales Problemas Diagnostico Guia 18SP Discos de Afilado Plazo Largo de AlmacenamientoMúltiples Dientes de Discos Tornado Shindaiwa Disco Guardachispas Maya la de Mantenimiento Mantenimiento o horas 139/150 CadaShindaiwa autorizado Torsión de correctas Horas 50 Cada Mantenimiento Horas 10/15 Cada Mantenimiento General Mantenimiento Horas 10 Cada MantenimientoDiario Mantenimiento Cuchilla una con Unidades Operando C2510 Disco un Usando Corte de Cabezal con Equipadas Máquinas Césped de Corte Unidad la de Condición la Verifique Motor del Mínima Marcha de Ajuste Motor del ParadaContinuación Motor del Arranque Mínima Marcha de Ajuste Motor del Arranque Combustible de Tanque el LlenandoCombustible de Mezcla De proporción a mezcla Cuchilla la Instalando Nylon de Cabezal del Instalación Continuación Ensamblaje Seguridad de tuercas las AprieteAcelerador del holgura la Ajuste Ajustes C2510 Mango Ensamblaje Ensamblar de Antes C2510 EspecificacionesProducto del Descripción Seguridad de Etiquetas Trabajo de Area del Alerta Esté Equipado Debidamente Operario El Seguridad de Instrucciones Limpios mangos los mantenga Siempre Contenido Humana reproducción la Nocivos efectos otros u congénitosAlerta Mantengase Cuidado con Trabaje Orador