Assembly and Adjustments | Shindaiwa LE2510, 81719 instruction

Assembly and Adjustments

Install Gearcase Assembly

Figure 5

1.Loosen gearcase clamp screw.

2.Remove the gearcase index screw.

3.Slide the gearcase oriented as shown in Figure 5 onto the shaft tube insuring that the flex drive is engaged in the gearcase.

NOTE:

It may be necessary to pull the flex cable out from the shaft tube, engage into the gearcase and then slide the assembly onto the shaft tube.

4.Reinstall the index screw and tighten securely.

5.Tighten the clamp screw and torque to 52

–69 inch pounds.

Assembly and Adjustments

Adjust Throttle Lever Free Play

The throttle lever free play should be approxi- mately 3/16-1/4 inch (4-6 mm). See Figure

6.Make sure that the throttle lever operates smoothly without binding. If it becomes necessary to adjust the lever free play, follow the procedures and illustrations that follow.

3/16-1/4 inch (4-6 mm)

Figure 7

1. Loosen the air cleaner cover knob and

remove the air cleaner cover. See Figure 7.

2. Loosen the lock nut on the cable ad-

3.Turn the cable adjuster in or out as required to obtain proper free play 3/16-1/4 inch (4-6 mm). See Figure 8.

4.Tighten the locknut.

Cable

Adjuster

Figure 6

Throttle Free Play

juster. See Figure 8.

5. Reinstall the air cleaner cover.

Image 6

Shindaiwa LE2510, 81719 manual Assembly and Adjustments, Adjust Throttle Lever Free Play

Contents

LE2510 Lawn Edger Contents Introduction Safety Instructions Properly Equipped Operator Safety Labels Be Aware of the Working Environment Specifications Prior to AssemblyProduct Description Assembly and Adjustments Adjust Throttle Lever Free Play Mixing Fuel Filling the Fuel TankExamples of 501 mixing quantities When the Engine Starts Starting the Engine Stopping the Engine Adjusting Engine IdleIdle Speed Adjustment Checking Unit Condition To adjust blade height Using a Hand-held EdgerAdjusting the Blade Guidelines for Operating the Edger General Maintenance Daily MaintenanceHour Maintenance Quently in dusty or dirty conditions 10/15-Hour MaintenanceEvery 50 hours of operation more fre Every 10 to 15 hours of operation 139/150-Hour Maintenance Valve AdjustmentInspect the Gearcase Protector Long Term Storage Spark Arrester Screen MaintenanceReplacing the Edger Blade Exhaust Port Inspection Troubleshooting Guide Engine does not Start Additional Problems Manufacturers Warranty Coverage Telephone 503 731-3167, Japan Fax 81-82-849-2481 8492 Corporation Shindaiwa Com.shindaiwa.www 50 69366962 -FaxOregon Tualatin Rd Herman .W.S Inc Shindaiwa Garantía DE Servicio DE Solicitudes Continuación Diagnostico Guia Adicionales Problemas Diagnostico Guia Potencia Baja Guardachispas Maya la de Mantenimiento Plazo Largo de AlmacenamientoOrilladora la de Cuchilla la Reemplazar Cilindro del Escape de Inspección Horas 139/150 Cada Mantenimiento Continuación Horas 50 Cada MantenimientoEngranajes de Caja la de Protector el Inspeccione Horas 50 Cada Mantenimiento Horas 10/15 Cada Mantenimiento Horas-10 Cada Mantenimiento Diario MantenimientoGeneral Mantenimiento Cuchilla La De Ajuste El Mano de Orillador el UtilizandoRecauciónP Unidad la de Condición la Verifique Motor del Mínima Marcha de AjusteMotor del Parada Motor el arrancar para ente Motor del Arranque…motor el arranca Cuando Rápidam jale luego resistencia, sienta Combustible de Tanque el Llenando Combustible de MezclaDe proporción Pulgadas 1/4-/163 Ajustes y EnsamblajeSeguridad de tuercas las Apriete Acelerador del Holgura la Ajuste Especificaciones Ensamblar de Antes Seguridad de Etiquetas Trabajo de Area del Alerta Esté Alerta Mantengase Equipado Debidamente Operario ElSeguridad de Generales Instrucciones Cuidado con Trabaje Contenido Seguridad de Declaraciones Introducción Rev 81719 pieza de Número