Placing the Regulator in Service

Page 9

The following checks will be useful in assuring the regulator is ready for use. The list cannot be all inclusive; careful at- tention on the part of a qualified operator remains imperative.

BEFORE CONNECTING

•Check oil level at oil sight window. If low, add sufficient oil (ASTM D-3487 Type II) to bring to desired level.

•Check oil dielectric strength per ASTM D 877. If found below 25kV, oil should be changed or reconditioned. Reference ANSI C57.106-2002. Note: Oil tests are not required for new equipment.

•Perform insulation power factor test per ANSI C57.15. Maximum value is 2.0%.

•Verify from the nameplate that the unit is connected for the proper output voltage, motor voltage and control panel voltage.

•Assure that the regulator is on the neutral tap position. This should be accomplished by observing the position indicator pointer and by powering the control from a 120V external source and observing the NeutraliteTM to be illuminated.

BEFORE CONNECTING

•Identify 'S', 'L' and 'SL' bushings on the cover. Make elec- trical connections per the appropriate installation diagrams, page 4, first connecting 'SL' bushing.

•Set Vari-AmpTMlimits on position indicator, if necessary. See Page 11.

•Set Accu/StatTM Control as desired. See Accu/StatTM instruction manual.

SWITCHING “ON-LINE”

•Improper by-pass operation will result in explosion and fire hazard. Will cause serious injury, death or equipment damage.

•Do NOT place into service unless tap-changer is in neutral position AND control panel is properly disabled.

Improper By-Pass operation will result in explosion and fire hazard. Will cause serious injury, death or equipment damage.

To Prevent:

Do NOT install OR remove from

service unless Tap Changer is in neutral position AND Control Panel is properly disabled to prevent tap changes while in By-Pass configuration. Read Operators Manual before attempting to By- Pass this Regulator.

Follow instructions to place into service:

1.Place the Auto/Manual switch in the By-Pass position

2.Place the Raise/Lower switch in "Off"

3.Make certain regulator is in neutral (N) position

4.Turn voltage power source switch to "Off"

5.Remove power fuse

6.Close, sequentially, the source and load switches

7.Open the bypass switch

8.Visually observe that bypass circuit has opened

9.Replace power fuse

10.Place voltage power source switch to "Normal."

CHECKING REGULATOR OPERATION

1.Refer to applicable Accu/StatTM Control instruction manual.)Turn the Tap Control switch to MANUAL.

2.Run the tapchanger in the lower direction, at least until the control is observed to go out of band "LOW".

3.Turn the Tap Control switch to AUTO. After a time delay, the regulator will return to an "IN" band condition.

4.Turn the Tap Control switch to MANUAL.

5.Run the tapchanger in the raise direction, at least until the control is observed to go out of band "HIGH".

6.Turn the Tap Control switch to AUTO. After a time delay, the regulator will return to an "IN" band condition.

21-115532-001 specifications

The Siemens 21-115532-001 is an innovative device designed to enhance operational efficiency across various industrial applications. This equipment embodies the technology and reliability that Siemens is known for, making it a preferred choice among professionals in the field.

One of the primary features of the Siemens 21-115532-001 is its advanced control capabilities. The device integrates seamlessly with existing industrial automation systems, enabling real-time monitoring and control. This allows users to adjust parameters dynamically and respond swiftly to changing operational conditions, ultimately leading to improved productivity and reduced downtime.

The device is equipped with robust communication technologies that facilitate data exchange with other industrial components. This includes compatibility with industry-standard protocols such as Profinet and EtherNet/IP, allowing for smooth integration into diverse ecosystems. The ability to connect with cloud-based systems enhances its functionality, providing valuable insights through data analytics.

In terms of physical characteristics, the Siemens 21-115532-001 is designed for durability. Housed in a rugged casing, it can withstand harsh industrial environments, ensuring longevity and reliability. It is waterproof and resistant to dust, making it suitable for use in outdoor settings or locations with challenging conditions.

The Siemens device also emphasizes safety features. It complies with international safety standards, ensuring that it can be safely integrated into various operations without compromising overall system integrity. This makes it an ideal choice for industries where safety is paramount.

Another significant aspect of the Siemens 21-115532-001 is its user-friendly interface. The device includes intuitive software that simplifies configuration and operation. Users can easily navigate through settings and features, reducing the learning curve and allowing for faster deployment in industrial applications.

In conclusion, the Siemens 21-115532-001 represents a combination of cutting-edge technology, robust design, and operational flexibility. Its advanced features and characteristics make it a vital asset for businesses looking to enhance their industrial processes. With its reliability and efficiency, it stands out as a leading choice in the market for industrial control solutions.

Siemens 21-115532-001 manual Placing the Regulator in Service

Models: 21-115532-001