Electrical

connection

￿ WARNING

￿

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Power cord must be connected

￿ WARNING

￿

 

 

by a licensed

electrician

only.

 

 

 

 

 

 

 

 

Use only a U.L. approved

 

 

Power cord must be connected

 

 

 

by

a qualified person

only.

 

30￿amp power cord with strain

Connect

to

individual

Brunch

 

relief

clamp -

 

 

 

 

 

 

note

manufacturer's instructions.

Circuit.

 

 

 

 

 

 

 

 

 

 

 

 

Do

not

plug end of

power

cord

 

 

 

 

 

 

 

 

Do

not

use

an

adapter.

 

into

a

live receptacle

before

con:

 

 

 

 

 

 

 

 

Do

not

use

an

extension cord.

necting power cord to appliance

 

 

 

 

 

 

 

 

Do

not

remove

ground

prong.

terminals and

closing

junction/

 

 

 

 

 

 

 

 

splitter

box as

described

below.

 

 

 

 

 

 

 

 

For

CANADA

 

 

 

 

 

Do

not

reuse

old power

cord.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cord must have closed loop or

Your dryer comes with a power

upturned end

wire terminating

supply cord,

CSA

listed

in Canada.

connectors.

 

 

 

 

 

The Siemens dryer requires a 4:wire Do not make a sharp bend or

receptacle.crimp wiring/conductor at con: nections.

 

 

 

 

 

 

 

 

 

Only

a 4:conductor cord

shall

 

 

 

 

 

 

 

 

 

be￿used when the appliance is

 

 

 

 

 

 

 

 

 

installed in

a mobile home or an

 

 

 

 

 

 

 

 

 

area

where

the local

codes do

 

 

 

 

 

 

 

 

 

not

permit

grounding

through

 

 

 

 

 

 

 

 

 

the

neutral.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Connecting

4)wire power

supply

 

 

 

 

 

 

 

 

cord

 

 

 

 

 

 

 

 

When installing

the

receptacle for

1. Remove

the screws

from the

 

cover of the terminal block

the dryer cord,

ensure

that the

 

 

located at the top rear of the

power supply

cord

is

accessible

 

 

appliance.

 

 

 

 

 

when the dryer is in the installed

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

position.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

The power cord should only be

 

 

 

 

 

 

 

 

 

 

replaced

by a

 

qualified

person.

 

 

 

 

 

 

1

 

 

Use￿a 4:wire power supply cord

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

(see

electrical

connection

U.S.A.

 

 

 

 

 

 

2

 

 

below).

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

For

U.S.A.

 

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

Your dryer comes without a power

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

supply cord.The power cord must

 

 

 

 

 

 

 

 

 

 

meet the following

requirements:

 

 

 

 

 

 

 

 

 

 

-

UL

listed

in

the

USA

1

-

terminal block

 

 

 

 

 

-

208

; 240

volt

rated

(minimum)2

-

grounding

strap

 

 

 

 

 

3.Fix the strain relief clamp to the angle bracket. Tighten the nut.

4.Loosen the 2 screws labeledL and the screw labeledN in the terminal block. and the screw of the GROUND terminal.

5.Thread the 4 wire cable through the U.L. strain relief clamp.

6.Tighten the screws (2.5￿Nm) of the U.L. strain relief clamp so that the power cord cannot be moved.

7.Attach the power cord ground conductor (green) to the GROUND terminal. Tighten the screw (2.5 Nm) so that the ground conductor is held securely in place.

8.Attach the 2 power cord outer conductors (red and black) to the 2 terminals labeled L and the remaining power cord conductor (white) to the terminal labeled N.

9.Tighten all 3￿screws (3 Nm) so that the power conductors are held securely in place .

-30 amps

-Type SRDT or DRT (UL 2158)

-Five feet long (minimum)

3 - Angle bracket for strain relief clamp

2.Loosen the bottom screw of the grounding strap. Place the screw to the GROUND location. Planish the grounding strap and hang loosely.

8

Page 9
Image 9
Siemens WTXD5300US manual Electrical Connection, Usa