![](/images/new-backgrounds/1213552/21355225x1.webp)
Assembly and Adjustments
Blade dimensions: 4-3/8” (110mm) diameter 3/4” Arbor
MIN RPM 11,000/min
impoRTANT: The saw blade provided on this tool has a
To reduce the risk of injury, do not use extra thin kerf saw blades. The kerf of the blade must be wider than .061”. Extra thin kerf
saw blades (less than .061”) may cause the work piece to bind against the riving knife during cutting. It is recommended that the kerf of the replacement blade used on this saw be .061” or more.
To reduce the risk of injury, do not use saw blades made with a thick body plate. If the replacement saw blade's plate thickness
is greater than .057”, the riving knife would not properly serve as an aid to reduce kickback. The replacement blade's plate thickness must be less than .057”.
changing the Blade
NoTe: Clean blade of any excess oil before installation.
1.Slide the saw assembly back to its farest position. This is the position in which the blade can be removed from saw.
2.Using a phillips head screwdriver, remove the rear screw on the blade bolt cover and rotate the cover clear of the blade bolt.
3.Push and hold in the arbor lock to lock the blade in place. Using the hex wrench (included), turn the blade bolt clockwise to remove it.
NoTe: The blade bolt has a left hand thread.
5.Remove the blade bolt and blade collar.
6.Remove blade by sliding it down through the kerf insert and out through the underside of the table.
NoTe: Inner washer does not need to be removed.
7.Install a
NoTe: Make sure the rotation arrow on the blade matches the rotation arrow on the upper guard.
FIG. 3
.059” |
|
|
|
|
|
|
|
| RIVING KNIFE | |||
|
|
|
|
|
|
|
| |||||
|
|
|
|
|
|
|
|
|
|
| COUTEAU DIVISEUR | |
|
|
|
|
|
|
|
|
|
|
| CUCHILLA SEPARADORA | |
MUST BE .061” OR MORE |
|
|
|
|
|
|
|
|
|
|
| KERF WIDTH |
|
|
|
|
|
|
|
|
|
|
| LARGEUR DE VOIE | |
|
|
|
|
|
| |||||||
DOIT ÊTRE DE 0,061 PO OU PLUS |
|
|
|
|
|
|
|
| ANCHURA DE LA SECCIÓN DE CORTE | |||
|
|
|
| |||||||||
DEBE SER 0.061 PULGADAS O MÁS |
|
|
|
|
|
| BLADE TEETH | |||||
|
|
|
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
| DENTS DE LA SCIE | ||
|
|
|
|
|
|
|
|
|
| DIENTES DE LA HOJA | ||
MUST BE LESS THAN .057” |
|
|
|
|
|
|
| BLADE BODY PLATE | ||||
DOIT ÊTRE DE MOINS DE 0,057 PO |
|
|
|
|
|
| PLAQUE DU CORPS DE LA LAME | |||||
DEBE SER MENOS DE 0.057 PULGADAS |
|
|
|
|
|
| PLACA DEL CUERPO DE LA HOJA |
FIG. 4 |
Arbor lock |
Blade Bolt |
cover |
Blade Slot |
| FIG. 5 | |
Rotation |
| |
Arrow |
| |
Remove and | Rotation | |
insert blade thru | ||
of blade | ||
slot in rear of table | ||
|
13.