MultiLink®
MINI GARAGE DOOR REMOTE
WITH FLASH LIGHT | MODEL : CG5 |
1. INTRODUCTION
Thank you for your purchase of the MultiLink® garage door remote control, Model CG5. This remote is designed to work with the Chamberlain® “Security +”, Genie® “Intellicode” and Chamberlain® Billion code. This remote is also capable to operate the mentioned brands garage door opener with the newer 315MHz garage door openers or the older one at 390MHz. Please follow the details instructions below in order to setup the new transmitter to work with your existing opener.
2. SELECT THE FREQUENCY
Check with your garage door opener to determine it is
Brand | Frequency |
|
|
Chamberlain® with learn button color: Purple | 315MHz |
|
|
Chamberlain® with learn button color: Green, White, | 390MHz |
Grey, Yellow |
|
|
|
Chamberlain® with learn button color: Orange, Red | 390MHz |
|
|
Genie® | Either 315MHz or 390MHz |
| (check on your garage door |
| opener) |
|
|
The default frequency setting is at 390MHz. Follow the procedure below to change this frequency setting.
1.Open up the case with a coin.
2.Remove the frequency jumper.
3.Secure the frequency jumper to the 2 connector posts.
3. SELECT THE BRAND (CONT)
Once you have setup the frequency and brand setting of your remote control, following the instructions below to learn the remote to your garage door opener.
4. PROGRAMMING
You should find a “learn” button from your existing garage door opener (the unit with the motor located on the ceiling of your garage). Press and hold this “Learn” button for 2 seconds and then release. The LED light located beside the ‘Learn’ button will go on. Then press the garage door button on your new transmitter for 1 second and then release to activate it. The LED light on your existing
garage door opener will flash then go off. Your remote control is now programmed to your existing garage
door opener and will operate your garage door.
5. TROUBLESHOOTING
If the garage door cannot be activated, check the followings:
-The red light LED should come on when the button is pressed, if not, check the battery and its polarity, ensure it is inserted properly.
-Repeat programming again to ensure the new transmitter is programmed.
6.OPERATION
4. Table below shows the frequency setting with different jumper configurations.
315MHz | 390MHz |
Press and hold the plastic case where it marks “PRESS” to activate the flash light.
Press the garage door opener button will activate your garage door.
® |
Garage Door Button
Jumper (connected at right 2 posts) | 315MHz |
Jumper (connected at left 2 posts) | 390MHz |
3. SELECT THE BRAND
Depends on what brand of garage door opener you have, the brand jumper setting is different. The brand jumper setting is the red jumper next to the battery.
Brand | Brand jumper setting |
|
|
Chamberlain® with learn button color: Purple, Orange, Red | Connecting Jumper on |
| posts 1 & 2 |
|
|
Chamberlain® with learn button color: Green, White, | Connecting Jumper |
Grey, Yellow | on posts 3 & 4 |
|
|
Genie® | Connecting Jumper on |
| posts 2 & 3 |
|
|
1 2 3 4 | 1 2 3 4 | 1 2 3 4 |
Posts 1 & 2 | Posts 2 & 3 | Posts 3 & 4 |
7. BATTERY
Positive "+"
Up
One 3 volt Lithium type (CR2032) battery is included.
Replacing the battery.
1.Open the case with a corn.
2.Slide the old battery away from the battery holder.
3.Slide in the new battery with the positive (+) side facing up.
4.Firmly close the case.
8. WARNING
If this transmitter triggers other garage doors in your neighborhood, change all your transmitters and receiver to a new code setting.
DO NOT let children use the garage door transmitter without adult supervision. Children can injure themselves or others by the garage door.