ARCNET 5 Port HUB Controller
Datasheet
Option Feature for Jitter FilteringWhen any RX ports receive the bigger jitter than its allowance, the TMC2005 may fail to receive the data correctly and the network may be down.. However the below method to escape is effective for the case that a momentary big jitter occurs under a special condition like an optical transceiver.
1)Big jitter (BJ) modeThe reference phase of the internal DPLL is changed from the first pulse to the second pulse by setting “0” to the big jitter mode pins (nBJX). This setup is effective for the case that a big jitter occurs when rising up from DC state as same as when using an optical transceiver with ATC function (refer to complement).
Note: The delay time of the TMC2005 becomes 400nS (at 2.5Mbps) longer than the normal mode. The delay time limits the maximum cable length and maximum node number.
[Complement] The big jitter may occur in the case of using an optical transceiver, especially an optical receiver that has an ATC circuit that controls threshold level in proportion to received light strength. The first pulse especially after long time idle has the big jitter but the second pulse is stabilized.
2)Changing polar of RX portIn order to filter the jitter of edge in one side, it is effective to set reverse to pin SA, SB, SE to change the polarity of RX port.
Note: Changing the polarity of RX port makes the delay time of the TMC2005 circuit a half bit (200nS) longer than original 2.5Mbps, and the delay time affects the maximum cable length and maximum node number.
Option Feature for Noise Cut modeThe Noise cut mode is enabled by setting pin nMBx sets 0. The noise cut mode is a function to remove the ringing noise and the reflection noise generated on the leading edge side of the input pulse to receive data input RXINx. The position and the width of the “dead band” are shown in the figure below.
- Dead band at Normal mode (nMBx=1) |
| - Dead band at Noise cut mode (nMBx=0) | |||||||||||||||||||||||
|
|
|
|
|
| Period of data rate (Tdr) |
|
|
|
|
|
|
|
| Period of data rate (Tdr) |
|
|
| |||||||
|
|
|
|
|
|
|
|
|
| ||||||||||||||||
|
|
|
|
| Tdr/8 = 1 clock |
|
|
|
|
|
| Tdr/8 = 1 clock |
|
| |||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RXIN |
|
|
|
|
|
|
|
|
|
|
| RXIN |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||
(Active High) |
|
|
|
|
|
|
|
|
|
| (Active High) |
|
|
|
|
|
|
|
|
|
|
|
| ||
Ideal waveform |
|
|
|
|
|
|
|
|
| Ideal waveform |
|
|
|
|
|
|
|
|
|
|
| ||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
| dead band |
|
|
|
|
|
|
|
|
| dead band: Noise cut band |
|
|
|
| |||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
RXIN edge reference position:
Generated by adjacent phase of SYNC character (1,1,0)
RXIN edge reference position:
Generated by adjacent phase of SYNC character (1,1,0)
SMSC | Page 11 | Revision 1.1 |
DATASHEET