Manuals / Brands / Lawn and Garden / Lawn Mower / Snapper / Lawn and Garden / Lawn Mower

Snapper 5900830 S200XTBV2861, 61 Cut Zero-Turn Riding Mower Control Functions, Ground Speed Levers, Seat Adjustment Lever, Ignition Switch

1 56

Download 56 pages, 5.25 Mb

Features and Controls

	ReproductionThe ignition switch starts and stops the engine, it has three
Figure 2. Control Locations		orf
Control Functions	Not

The information below briefly describes the functi n of in ivi al controls. Starting, stopping, driving, and mowing require the combined use of several controls applied in specific sequences. To learn what combination and sequence of controls to use for various tasks see the OPERATION section.

	Ground Speed Levers				Seat Adjustment Lever
	Ground Speed Levers				Seat Adjustment Lever
These levers control the ground speed of the rid r. The left			The seat can be adjusted forward and back. Move the lever
lever controls the left rear drive wheel and the right l v r			towards the left, position the seat as desired, and release the
controls the right rear drive wheel.			lever to lock the seat in position.
Moving a lever forward increases the FO WA D speed of
Moving a lever forward increases the FO WA D speed of
the associated wheel, and pulling back on a lever increases					Ignition Switch
the REVERSE speed.
Note: The further a lever is moved away from the			positions:
neutral position the faster the drive wheel will turn.
See the Operation section for proper steering						OFF	Stops the engine and shuts off the
See the Operation section for proper steering
instructions.
							electrical system.
						RUN	Allows the engine to run and powers
							the electrical system.
						START	Cranks the engine for starting.

NOTE: Never leave the ignition switch in the RUN position with the engine stopped–this drains the battery.

14	www.SnapperPro.com

Contents

Model Operator’s Manual S200XT Series Zero-TurnRiding Mowers Reproduction Descripti n WARNING Table of Contents Operating Safety Children Slope Operation Thrown Objects Moving Parts Roll Bar Use Retaining Walls, Drop offs, and Water Overhead Obstacles Fuel and Maintenance Enclosed Areas TRAINING PREPARATION OPERATION TOWED EQUIPMENT (RIDE-ONUNITS) SLOPE OPERATION Page Page Page Page Operational SAFETY Checks NOTICE Features and Controls Identification Numbers Control Functions Ground Speed Levers Seat Adjustment Lever Ignition Switch Parking Brake Fuel Tank Cap Fuel Level Gauge PTO (Power Take Off) Switch Deck Lift Pedal, Cutting Height Operation General Operating Safety Checks Before Starting Check Tire Pressures Seat Adjustment Mowing Height Adjustment Foot Pedal Adjustment Raise and Lower the Roll Bar Starting the EnginePushing the Rider By Hand Stopping the Rider Operation Zero Turn Driving Practice Practice Turning Around a Corner Practice Turning In Place Executing an End-Of-RowZero Turn Mowing Mowing Recommendations Mowing Methods Attaching A Trailer Regular Maintenance Maintenance Schedule Checking / Adding Fuel Fuel Filter Engine Maintenance Change Oil & Filter Inspect Muffler and Spark Arrester Lubrication Check Hydraulic Oil Level Change Hydraulic Oil Filter Servicing The Mower Blades Sharpening the Mower Blade •Always wear gloves when handling the mower blades •Always wear safety eye protection when grinding Balancing the Mower Blades Avoid injury! Keep mower blades balanced Ground Speed Control Lever Adjustment Speed Balancing Adjustment Neutral Adjustment Parking Brake Adjustment Deck Rod Timing Adjustment - 61” Models Deck Leveling Adjustment - 61” Models Deck Rod Timing Adjustment - 72” Deck Leveling Adjustment - 72” Models Mower Belt Replacement Check the Mower Belt Idler Tensioner Spring Length Adjusting the Mower Belt Idler Spring Length Deck Lift Assist Springs Hydraulic Pump Drive Belt Replacement Battery Maintenance Regular Maintenance Battery Service Discharged Vehicle Battery Storage Starting After Long Term Storage Troubleshooting Troubleshooting Chart Troubleshooting the Rider Troubleshooting Troubleshooting the Mower Troubleshooting Common Cutting Problems Specifications Specifications 26 Gross HP† Kawasaki 28 Gross HP* Briggs & Stratton 32 Gross HP* Briggs & Stratton 25.5 Gross HP† Kawasaki SLOPE INDENTIFICATION GUIDE LINE INSTRUCTIONS FOLD (TREE,POLE,FENCEPOST,BUILDING,ETC)