Regular Maintenance
Transmission Drive Belt Replacement | 8. Remove the old belt and replace it with the new one. | |
1. Park the unit on a smooth, level surface such as a | Make sure that the | |
of the crankshaft pulley and transmission pulleys (B & | ||
concrete floor. Disengage the PTO, engage the parking | ||
C). | ||
brake, turn off the engine and remove the ignition key. | ||
|
9. Reinstall the spring anchor eyebolt (G) into the anchor
2. Loosen and remove the hardware that secures the
tab and loosely fasten the nut. Adjust the anchor eyebolt
skid plate assembly (A, Figure 31) to the engine deck.
until a
Remove the skid plate assembly from the engine deck.
achieved. Tighten the nut.
3. Remove the PTO drive belt (see MOWER BELT |
| 10. Using the hardware that was previously removed reinstall | ||||||||
| REPLACEMENT for removal instructions.) |
| ||||||||
|
|
| the clutch anchor to the engine deck. |
| ||||||
4. Cut the wire tie that secures the PTO clutch wire harness |
|
| ||||||||
NOTE: Make sure that the slot in the PTO clutch lines up with | ||||||||||
| to the engine deck frame. |
|
| |||||||
|
|
| the PTO clutch mounting tab (C, Figure 31) underneath the | |||||||
5. | Unplug the PTO clutch wire harness from the PTO clutch | |||||||||
engine deck. |
|
|
| |||||||
| (B). |
|
| 11. Reconnect the PTO clutch wire harness to the PTO | ||||||
6. Loosen and remove the hardware that secures the PTO |
| |||||||||
|
| clutch. |
|
|
|
| ||||
| clutch mounting tab (C) to the engine deck. Remove the |
|
|
|
|
| ||||
| 12. Using a new wire tie secure the PTO clutch wire harness | |||||||||
| PTO clutch mounting tab. |
|
| |||||||
|
|
|
| to the frame and away from moving components. | ||||||
7. Loosen the nuts on the spring anchor eyebolt (G, Figure |
|
| ||||||||
| 13. Reinstall the PTO drive belt. |
|
| |||||||
| 32) to release the majority of the belt tension. Use |
|
|
| ||||||
|
| 14. Using the hardware that was previously removed reinstall | ||||||||
| caution and remove the nut to completely release the |
| ||||||||
| tension. |
|
|
| the skid plates to the engine deck. |
| ||||
|
| Reproduction |
|
| ||||||
|
| C | for | F | G |
|
| |||
|
| Not |
|
|
|
| I |
|
| |
|
|
|
|
|
|
| H |
|
| |
|
|
|
|
| A |
|
|
|
| |
|
|
|
| E |
|
|
|
| ||
|
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
| (12,4 cm) | |
|
|
|
|
|
| D | H |
|
| |
|
| B |
|
|
| B |
|
|
| |
|
|
|
| C |
|
| C |
| ||
|
|
|
|
|
|
|
| |||
|
|
|
| Figure 32. Hydraulic Pump Drive Belt Replacement | ||||||
|
|
|
| A. | Transmission Drive Belt |
|
| |||
|
|
|
| B. | Crankshaft Pulley |
|
| |||
| A |
|
| C. | Transmission Pulleys |
|
| |||
|
|
|
| D. | Idler Pulley |
|
| |||
|
|
|
| E. | Idler Arm |
|
|
| ||
Figure 31. Remove the PTO Clutch Mounting Tab |
| F. | Spring |
|
|
|
| |||
| G. | Spring Anchor Eyebolt |
|
| ||||||
A. | Skid Plate Assembly |
|
| H. | Stationary Idler Pulley |
|
| |||
B. | PTO Clutch |
|
| I. | Arrow Indicating the Front of the Machine |
C. PTO Clutch Mounting Tab
32 | www.SnapperPro.com |