|
|
| Unpacking and Assembly | |
Your rototiller comes fully assembled except for a few parts. The fol- |
| |||
|
|
| ||
IMPORTANT |
| |||
lowing instructions will help you unpack your tiller and assemble and |
| |||
adjust your tiller’s depth regulator lever, cable tension and handlebar | THE RIGHT AND LEFT SIDES OFYOUR |
| ||
height. You will need 2- 9/16” wrenches. |
| |||
ROTOTILLER ARE DETERMINED FROM |
| |||
|
|
| ||
UNPACK TILLER | THE OPERATING POSITION AS YOU |
| ||
FACE THE DIRECTION OF FORWARD |
| |||
1. Open top of carton and remove handlebar assembly. | TRAVEL. |
| ||
ENGINE IS SHIPPED FROM FACTORY |
| |||
2. Find parts packet. Parts packet contains: |
| |||
WITHOUT OIL.YOU MUST ADD ENGINE |
| |||
| 4- | OIL BEFORE STARTING ENGINE. |
| |
|
|
|
| |
| 4- | TILLER TRANSMISSION IS SHIPPED |
| |
| 1- | FROM FACTORY WITH THE PROPER |
| |
| 1- detent pin | AMOUNT OF LIQUID GREASE. |
| |
| 1- five star knob |
|
|
|
|
|
| ||
3. Cut open end of carton and remove machine by: |
|
|
| |
|
|
|
| a. Removing lock pins on wheels. |
|
| ! CAUTION |
|
| |
| b. Roll tiller from carton. |
|
|
|
| ||
|
|
|
|
|
|
| |
|
|
|
| DO NOT TRY TO LIFT THE ROTOTILLER FROM THE | |||
ATTACH HANDLEBAR TO TILLER |
| CARTON. |
|
|
| ||
|
|
|
|
| |||
|
| Reproduction |
|
| |||
|
|
|
| DO NOT ADD ENGINE OIL INTO GEAR CASE DIP- | |||
1. | Place handlebar stems on outside of lower handlebar mount and | STICK HOLE. |
|
| |||
| align lower holes. (SEE FIGURE 1) |
|
|
|
|
|
|
2. | Insert one |
|
|
|
| ||
| desired handlebar height. |
|
|
|
|
|
|
3. | Start |
|
|
|
|
|
|
4. | Insert one |
|
|
|
| ||
5. | Tighten all |
|
|
|
|
| gear case |
|
|
|
|
|
|
| dipstick |
FILL ENGINE CRANKCASE |
|
|
|
|
|
| |
1. | Add oil according to engine manual. Do not overfill. Use a clean, |
|
|
| gear case | ||
|
|
| dipstick hole | ||||
| high quality detergent oil. Container must Notbe marked A.P.I. Se vice |
|
|
| |||
|
|
|
|
| |||
| SF - SJ. Use no special additives with recommended oils. Do not |
|
|
|
| ||
| mix oil with gasoline. Oil level must be full. Ch | ck the oil level |
| NO ENGINE OIL! | |||
| by removing oil fill plug. Oil level should be up to the bottom of the |
| |||||
| fill plug opening. |
|
|
|
|
|
|
2. | Always check oil level before starting engine. | efer to engine |
| lower handlebar |
| ||
| manual for capacity and type of oil to use. |
|
| ||||
|
|
| mount |
| |||
|
|
|
| nuts |
| ||
|
|
|
|
|
| ||
|
|
|
|
|
|
| bolts |
height handlebar
adjustment stem holes
FIGURE 17