Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper CP216019KWV, CRP216019KWV, CP215519HV Operation Continued, Handle Height Adjustment

Models: CRP216019KWV, CP216019KWV, CP215519HV CP216019KWV, CRP216019KWV, CP215519HV

1 28

Download 28 pages 2.2 Kb

Page 8

Operation (Continued)

Operation (Continued)

Starting and Operation (Continued)

Stopping

5.After the engine starts, turn off choke and allow a brief warm-up until the engine runs smooth before beginning mower operation.

NOTE: To stop the engine (and blade), release the blade control.

A

B

Operation

Figure 4: Starting the mower

Propelling the Mower

1.Start the engine. Refer to the Section entitled “Starting and Operation – Engine and Blade”.

2.Move the ground speed control (A, Figure 5) to the desired speed position.

3.Squeeze the wheel drive control (B) against the handle to engage the wheel drive and propel the mower forward. Forward speed can be adjusted while the mower is moving by changing the position of the ground speed control.

A

1.Stop forward motion of the mower by releasing the wheel drive control.

2.Stop the engine and blade by releasing the blade control.

Handle Height Adjustment

The height of the mower handle can be adjusted as follows:

1.Loosen the lower nuts (A, Figure 6) on each lower handle.

B

A

Figure 6: Adjusting the handle height

2.Move the handle assembly (B) up or down until the desired position is achieved.

3.Tighten the lower nuts on each lower handle to maintain the desired position.

!

WARNING

!

DO NOT attempt any maintenance, adjustments or service with engine and blade running. STOP engine and blade. Disconnect spark plug wire and secure away from spark plug. Engine and components are HOT. Avoid serious burns, allow sufficient time for all components to cool.

B

Figure 5: Mower drive controls

6	www.snapper.com

Image 8

Snapper CP216019KWV, CRP216019KWV, CP215519HV Operation Continued, Handle Height Adjustment, Propelling the Mower

Contents

21” STEEL DECK WALK MOWERS COMMERCIAL MODELS SERIES Safety Instructions & Operators Manual forModels CRP216019KWV CP216019KWV CP215519HVPRODUCT REGISTRATION Date of Purchase Retailer Retailers Phone Number EquipmentEngine Snapper at P.O. Box 777, McDonough, GeorgiaOperator Safety Features and Controls OperationMaintenance Operator Safety Features and Controls Operation MaintenanceImportant Operator Safety Instructions Protection for ChildrenSlope Operation PreparationImportant Operator Safety Instructions Continued Maintenance and StorageSafe Handling of Gasoline Continued From Previous Page OperationFeatures and Controls Features and ControlsFeatures and Controls Operation Pre-Start Check ListStarting and Operation Engine and BladeHandle Height Adjustment Figure 6 Adjusting the handle heightOperation Continued Propelling the MowerCutting Height Adjustment Figure 7 Adjusting cutting heightFigure 8 Cutting height settings approximate Recycling OperationInstalling the Discharge Deflector Installing the Grass Bag AdapterFigure 10 Installing the discharge deflector Figure 11 Installing the grass bag adapterInstalling the Recycling Plug Installing the Grass Bag Adapter ContinuedIMPORTANT Install the grass bag as a safeguard Figure 12 Installing the adapter standoffInstalling the Grass Bag Figure 14 Installing the grass bagDumping the Grass Bag NOTE An illustration of the Z-Fold is attached to the bagMaintenance Maintenance - IntroductionService - After First 5 Hours Check Grease Level in TransmissionMaintenance Continued Service - PeriodicStorage Procedure Check Mower BladeMower Blade Replacement Standard Blade Wear LimitNinja Blade Wear Limit Blade SharpeningWheel Drive Control Adjustment Self-Propelled Models Only Figure 24 Wheel drive control adjustmentBlade Sharpening Continued Figure 23 Sharpening the mower bladeDriven and Drive Disc Service Cleaning Drive Disc & Driven DiscDrive Spring Repair/Replacement Driven Disc AdjustmentDriven Disc Adjustment Continued Driven Disc Ring ReplacementFigure 29 Proper driven disc adjustment Figure 28 Adjusting the driven discDriven Disc Ring Replacement Continued Driven Disc Bearing ReplacementFigure 31 Removing the driven disc assembly Figure 33 Replacing the driven disc bearingBelt Service Engine Drive Belt Replacement Stretch Type BeltsMaintenance D C Replacing the Bearing On the Pulley End Of the Hex ShaftEngine Drive Belt Replacement Stretch Type Belts - Continued Transmission Poly-V Belt ReplacementA B C D E F G Figure 36 Removing the drive discMaintenance Service ScheduleMaintenance/Replacement Parts CORRECTIVE ACTION TroubleshootingPROBABLE CAUSE Warranties 2 YEAR LIMITED WARRANTYDISCLAIMER OF WARRANTY Page Page Page Product Specifications Common Service PartsPart Number Snapper Products