Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper LT180H42IBV, LT200H42IBV2, LT200H48IBV2 important safety instructions Adjustment & Repair

Models: LT180H42IBV2, LT200H42IBV2, LT200H48IBV2 LT180H42IBV, LT200H42IBV2, LT200H48IBV2

1 48

Download 48 pages 23.11 Kb

Page 30

Image 30

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.4.8.DECK BELT REMOVAL & REPLACEMENT 48" Deck Drive Belt

1.Place tractor on a firm level surface.

2.Turn engine "OFF". Remove key.

3.Remove mower deck. See Section on DECK REMOVAL.

4.Remove deck idler tension spring. Remove nuts that secure the spindle pulley covers. See Figure 4.35.

5.Remove belt.

6.Install new belt.

7.Reinstall both pulley covers.

8.Reinstall mower deck to tractor.

TOP VIEW OF

48” MOWER DECK

ELECTRIC

CLUTCH

PULLEY

ENGINE TO DECK

DRIVE BELT

PART No. 4-6926

TENSION

SPRING

SPINDLE PULLEY COVER

TENSION	SPINDLE TO SPINDLE
SPRING	MOWER BELT
	PART No. 2-8334

FIGURE 4.35

Page 30

Image 30

Snapper LT180H42IBV, LT200H42IBV2, LT200H48IBV2, LT180H42IBV2, LT200H42IBV2, LT200H48IBV2 Adjustment & Repair

Contents

MODELS Safety Instructions & Operator’s Manual forLAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES LT180H42IBV LT200H42IBV2 LT200H48IBV2PROTECTION AGAINST TIPOVERS IMPORTANT SAFETY INSTRUCTIONSPROTECTION FOR CHILDREN PROTECTION AGAINST TIPOVERSSAFE HANDLING OF GASOLINE IMPORTANT SAFETY INSTRUCTIONSPREPARATION OPERATIONMAINTENANCE IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE TOWINGTABLE OF CONTENTS Section 1 - FAMILIARIZATION COMPONENTSCONTROLS Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECKLIST2.2 OPERATOR’S SEAT ADJUSTMENT 2.2.1. FRONT TO REAR ADJUSTMENT Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. STARTING ENGINESee Figure Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION Continued 2.3.2. STARTING WHEEL DRIVESection 2 - OPERATING INSTRUCTIONS 2.4 STOPPING 2.4.3. STOPPING MOWER BLADESSection 2 - OPERATING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF 2.6.1. Rolling Hydro ModelsDANGER Section 2 - OPERATING INSTRUCTIONS3.1 INTRODUCTION Section 3 - MAINTENANCE3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OILAIR PRE CLEANER AIR CLEANER Section 3 - MAINTENANCESERVICE - EVERY 25 OPERATING HOURS 3.3.1. CHECK ENGINE 3.2.4. CHECK DECK DRIVE BELTENGINE MUST NOT START IF Section 3 - MAINTENANCE6. Air Filter - Single Cylinder Engine ENGINE SHOULD START IF3.3.4. CHECK BLADE BRAKE Section 3 - MAINTENANCE3.3.3. MOWER COMPONENTS 3.3.5. TRACTOR LUBRICATION 1. Front Wheel Bearings7. Steering Tie Rod Section 3 - MAINTENANCE3.3.5. TRACTOR LUBRICATION 6. Steering Drag Link 8. Park Brake LeverSection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR k. Proceed to check front to rear deck pitchFRONT LIFT Section 4 - ADJUSTMENT & REPAIRPLACE THREE 2 X 4 UNDER FRONT AND REAR OF DECK FRONT LIFT ARMREMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWN SWIVEL FRONT LIFT Section 4 - ADJUSTMENT & REPAIRREAR LIFT ROD REMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWNNEUTRAL ADJUSTMENT NUT TURN NUT CLOCKWISE TO REDUCE FORWARD CREEP Section 4 - ADJUSTMENT & REPAIRROTATE ADJUSTING NUT CLOCKWISE TO INCREASE BRAKING OR COUNTER ROTATE TO REDUCE “PLAY”Section 4 - ADJUSTMENT & REPAIR 4.3.3. SHIFTER ADJUSTMENT Continued from previous pageDANGEROUS CONDITION DO NOT USE ON MOWER Section 4 - ADJUSTMENT & REPAIRNEW BLADE WEAR LIMIT. CRACKS OR NOTCHES BEGIN TO APPEAR 22º TO 28º STANDARD BLADESection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR 9. Make note of hole used in sector platesSection 4 - ADJUSTMENT & REPAIR 42” DECK SHOWN Section 4 - ADJUSTMENT & REPAIRTraction drive belt replacement VIEW FROM UNDERNEATH TRACTORSection 4 - ADJUSTMENT & REPAIR 1. Place tractor on a firm level surfaceSection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR REMOVE ADJUSTING KNOBS AND MOVE SEAT FORWARDREMOVE POSITIVE + CABLE LAST REMOVE NEGATIVE CABLE FIRST Section 4 - ADJUSTMENT & REPAIR 4.5.5. BATTERY TESTINGAVAILABLE ACCESSORIES Section 4 - ADJUSTMENT & REPAIRSECTION 5 - ELECTRICAL SYSTEM ELECTRICAL - B & S TWIN CYLINDER ENGINESECTION 5 - ELECTRICAL SYSTEM ELECTRICAL - B & S SINGLE CYLINDER ENGINEPROBABLE CAUSE TROUBLESHOOTING GUIDEPROBLEM CORRECTIVE ACTIONTROUBLESHOOTING GUIDE TRACTOR MAINTENANCE SCHEDULEMAINTENANCE PARTS MOWER BLADES2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Call the Snapper Customer Relations Center atSERVICE NOTES SERVICE NOTES SERVICE NOTES Safety Instructions & Operator’s Manual for Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. PhoneLAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES