Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper LT180H42IBV, LT200H42IBV2, LT200H48IBV2 important safety instructions Adjustment & Repair

Models: LT180H42IBV2, LT200H42IBV2, LT200H48IBV2 LT180H42IBV, LT200H42IBV2, LT200H48IBV2

1 48

Download 48 pages 23.11 Kb

Page 26

9.Make note of hole used in sector plates.

Section 4 - ADJUSTMENT & REPAIR

WARNING

DO NOT attempt any adjustments, maintenance or service with the engine or blades running. STOP blades. STOP engine. Set brake. Remove key. Remove spark plug wire from spark plug and secure wire away from spark plug. Engine and components can be extremely hot. Avoid burns by allowing engine and components sufficient time to cool.

4.4.7.TRACTION DRIVE BELT REPLACEMENT 42” Mower Deck Removal (Continued From Previous Page)

8.Remove hair pin and flat washer from rear deck hanger bracket on both sides of tractor.

9.Make note of hole used in sector plates.

10.Slide sector plates off of rear deck hanger brackets. See Figure 4.21.

11.Slide deck from underneath machine.

SECTOR PLATES

REAR DECK

HANGER BRACKETSREMOVE HAIR PIN & WASHER

42” DECK SHOWN

FIGURE 4.21

12.Disconnect traction belt idler pulley spring from tractor frame. See Figure 4.22.

13.Loosen mounting nuts on traction drive belt tension and stationary idlers just enough to allow belt to clear belt guides. See Figure 4.23.

14.Remove traction drive belt from engine pulley top groove. Remove belt from transmission pulley.

15.Remove traction drive belt.

Traction drive belt replacement

1.Place new traction drive belt over transmission pulley and span to engine pulley.

2.Place belt into top groove of engine pulley.

3.Route belt through stationary and tension idlers. See Figure 4.24.

4.Make certain belt is within belt guides of idlers.

5.Reattach tension idler spring to tractor frame.

RIGHT REAR

TRACTOR

FRAME

DISCONNECT SPRING

FROM FRAME

FIGURE 4.22
STATIONARY	TRANSMISSION
IDLER	TRANSMISSION
PULLEYS	PULLEY

ENGINE	LOOSEN	TENSION
ENGINE	IDLER	TENSION
PULLEY	NUTS	IDLER

VIEW FROM UNDERNEATH TRACTOR

FIGURE 4.23

	TRANSMISSION
DRIVE BELT	PULLEY

TENSION

IDLER

STATIONARY

IDLER

STATIONARY IDLER

BRACKET

BELT GUIDE

STATIONARY IDLER

FIGURE 4.24

NOTE: When installing a new belt, make certain the stationary idler is mounted in the hole closest to the left hand side of the tractor.

6.Reinstall mower deck in reverse order of removal.

26

Image 26

Snapper LT180H42IBV, LT200H42IBV2, LT200H48IBV2 Adjustment & Repair, Make note of hole used in sector plates

Contents

MODELS Safety Instructions & Operator’s Manual forLAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES LT180H42IBV LT200H42IBV2 LT200H48IBV2PROTECTION AGAINST TIPOVERS IMPORTANT SAFETY INSTRUCTIONSPROTECTION FOR CHILDREN PROTECTION AGAINST TIPOVERSSAFE HANDLING OF GASOLINE IMPORTANT SAFETY INSTRUCTIONSPREPARATION OPERATIONMAINTENANCE IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE TOWINGTABLE OF CONTENTS CONTROLS Section 1 - FAMILIARIZATIONCOMPONENTS 2.2 OPERATOR’S SEAT ADJUSTMENT 2.2.1. FRONT TO REAR ADJUSTMENT Section 2 - OPERATING INSTRUCTIONS2.1 PRE-START CHECKLIST See Figure Section 2 - OPERATING INSTRUCTIONS2.3 STARTING & OPERATION 2.3.1. STARTING ENGINE Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION Continued 2.3.2. STARTING WHEEL DRIVESection 2 - OPERATING INSTRUCTIONS 2.4 STOPPING 2.4.3. STOPPING MOWER BLADESSection 2 - OPERATING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF 2.6.1. Rolling Hydro ModelsDANGER Section 2 - OPERATING INSTRUCTIONS3.1 INTRODUCTION Section 3 - MAINTENANCE3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OILAIR PRE CLEANER AIR CLEANER Section 3 - MAINTENANCESERVICE - EVERY 25 OPERATING HOURS 3.3.1. CHECK ENGINE 3.2.4. CHECK DECK DRIVE BELTENGINE MUST NOT START IF Section 3 - MAINTENANCE6. Air Filter - Single Cylinder Engine ENGINE SHOULD START IF3.3.4. CHECK BLADE BRAKE Section 3 - MAINTENANCE3.3.3. MOWER COMPONENTS 3.3.5. TRACTOR LUBRICATION 1. Front Wheel Bearings7. Steering Tie Rod Section 3 - MAINTENANCE3.3.5. TRACTOR LUBRICATION 6. Steering Drag Link 8. Park Brake LeverSection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR k. Proceed to check front to rear deck pitchFRONT LIFT Section 4 - ADJUSTMENT & REPAIRPLACE THREE 2 X 4 UNDER FRONT AND REAR OF DECK FRONT LIFT ARMREMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWN SWIVEL FRONT LIFT Section 4 - ADJUSTMENT & REPAIRREAR LIFT ROD REMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWNNEUTRAL ADJUSTMENT NUT TURN NUT CLOCKWISE TO REDUCE FORWARD CREEP Section 4 - ADJUSTMENT & REPAIRROTATE ADJUSTING NUT CLOCKWISE TO INCREASE BRAKING OR COUNTER ROTATE TO REDUCE “PLAY”Section 4 - ADJUSTMENT & REPAIR 4.3.3. SHIFTER ADJUSTMENT Continued from previous pageDANGEROUS CONDITION DO NOT USE ON MOWER Section 4 - ADJUSTMENT & REPAIRNEW BLADE WEAR LIMIT. CRACKS OR NOTCHES BEGIN TO APPEAR 22º TO 28º STANDARD BLADESection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR 9. Make note of hole used in sector platesSection 4 - ADJUSTMENT & REPAIR 42” DECK SHOWN Section 4 - ADJUSTMENT & REPAIRTraction drive belt replacement VIEW FROM UNDERNEATH TRACTORSection 4 - ADJUSTMENT & REPAIR 1. Place tractor on a firm level surfaceSection 4 - ADJUSTMENT & REPAIR REMOVE POSITIVE + CABLE LAST REMOVE NEGATIVE CABLE FIRST Section 4 - ADJUSTMENT & REPAIRREMOVE ADJUSTING KNOBS AND MOVE SEAT FORWARD Section 4 - ADJUSTMENT & REPAIR 4.5.5. BATTERY TESTINGAVAILABLE ACCESSORIES Section 4 - ADJUSTMENT & REPAIRSECTION 5 - ELECTRICAL SYSTEM ELECTRICAL - B & S TWIN CYLINDER ENGINESECTION 5 - ELECTRICAL SYSTEM ELECTRICAL - B & S SINGLE CYLINDER ENGINEPROBABLE CAUSE TROUBLESHOOTING GUIDEPROBLEM CORRECTIVE ACTIONTROUBLESHOOTING GUIDE TRACTOR MAINTENANCE SCHEDULEMAINTENANCE PARTS MOWER BLADES2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Call the Snapper Customer Relations Center atSERVICE NOTES SERVICE NOTES SERVICE NOTES LAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES Safety Instructions & Operator’s Manual forSnapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. Phone