Manuals / Snapper / Lawn and Garden / Lawn Mower

Snapper LT180H42IBV, LT200H42IBV2, LT200H48IBV2 Familiarization, Components, Controls

Models: LT180H42IBV2, LT200H42IBV2, LT200H48IBV2 LT180H42IBV, LT200H42IBV2, LT200H48IBV2

1 48

Download 48 pages 23.11 Kb

Page 6

Section 1 - FAMILIARIZATION

Section 1 - FAMILIARIZATION

CLUTCH/BRAKE PEDAL

CHOKE

LIGHT SWITCH

PARK

BRAKE

LEVER

DOWN

BATTERY (UNDER SEAT)

SEAT ADJUSTMENT KNOB (UNDER SEAT)

SPEED

CONTROL

LEVER

OVERRIDE

LEVER

CUTTING

HEIGHT

ADJUSTMENT

LEVER

DISCHARGE

DEFLECTOR

MOWING DECK (42” SHOWN)

BLADE

SWITCH

FAST

SLOW

	OPERATOR’S
	SEAT	ENGINE SPEED	IGNITION
	STEERING	ENGINE SPEED	IGNITION
	STEERING	CONTROL	KEY
	WHEEL

DASHBOARD CONTROLS

FUEL TANK (UNDER HOOD)

HOOD

HEADLIGHTS

ENGINE

FIGURE 1.1

COMPONENTS

The nomenclature drawings above, illustrate the essential components of the SNAPPER Lawn Tractor. It is recommended that all operators of this equipment become thoroughly familiar with the components and their operation BEFORE OPERATING. Specific details involving the engine are found in the separate Engine Owner’s Manual.

Study the Important Safety Instructions, this Operator’s Manual and Engine Owner’s Manual before operating this machine. Keep these manuals available for future reference.

CONTROLS

All operators should be acquainted with the operator’s controls before attempting start-up or operation of the Lawn Tractor. See the Control Panel drawing above.

6

Image 6

Snapper LT180H42IBV, LT200H42IBV2, LT200H48IBV2 important safety instructions Familiarization, Components, Controls

Contents

MODELS Safety Instructions & Operator’s Manual forLAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES LT180H42IBV LT200H42IBV2 LT200H48IBV2PROTECTION AGAINST TIPOVERS IMPORTANT SAFETY INSTRUCTIONSPROTECTION FOR CHILDREN PROTECTION AGAINST TIPOVERSSAFE HANDLING OF GASOLINE IMPORTANT SAFETY INSTRUCTIONSPREPARATION OPERATIONMAINTENANCE IMPORTANT SAFETY INSTRUCTIONSMAINTENANCE TOWINGTABLE OF CONTENTS Section 1 - FAMILIARIZATION COMPONENTSCONTROLS Section 2 - OPERATING INSTRUCTIONS 2.1 PRE-START CHECKLIST2.2 OPERATOR’S SEAT ADJUSTMENT 2.2.1. FRONT TO REAR ADJUSTMENT Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION 2.3.1. STARTING ENGINESee Figure Section 2 - OPERATING INSTRUCTIONS 2.3 STARTING & OPERATION Continued 2.3.2. STARTING WHEEL DRIVESection 2 - OPERATING INSTRUCTIONS 2.4 STOPPING 2.4.3. STOPPING MOWER BLADESSection 2 - OPERATING INSTRUCTIONS 2.6. ROLLING TRACTOR WITH ENGINE OFF 2.6.1. Rolling Hydro ModelsDANGER Section 2 - OPERATING INSTRUCTIONS3.1 INTRODUCTION Section 3 - MAINTENANCE3.2 SERVICE - AFTER FIRST 5 HOURS 3.2.1. CHANGE ENGINE OILAIR PRE CLEANER AIR CLEANER Section 3 - MAINTENANCESERVICE - EVERY 25 OPERATING HOURS 3.3.1. CHECK ENGINE 3.2.4. CHECK DECK DRIVE BELTENGINE MUST NOT START IF Section 3 - MAINTENANCE6. Air Filter - Single Cylinder Engine ENGINE SHOULD START IF3.3.4. CHECK BLADE BRAKE Section 3 - MAINTENANCE3.3.3. MOWER COMPONENTS 3.3.5. TRACTOR LUBRICATION 1. Front Wheel Bearings7. Steering Tie Rod Section 3 - MAINTENANCE3.3.5. TRACTOR LUBRICATION 6. Steering Drag Link 8. Park Brake LeverSection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR k. Proceed to check front to rear deck pitchFRONT LIFT Section 4 - ADJUSTMENT & REPAIRPLACE THREE 2 X 4 UNDER FRONT AND REAR OF DECK FRONT LIFT ARMREMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWN SWIVEL FRONT LIFT Section 4 - ADJUSTMENT & REPAIRREAR LIFT ROD REMOVE WASHER & HAIR PIN ROTATE SWIVEL UP OR DOWNNEUTRAL ADJUSTMENT NUT TURN NUT CLOCKWISE TO REDUCE FORWARD CREEP Section 4 - ADJUSTMENT & REPAIRROTATE ADJUSTING NUT CLOCKWISE TO INCREASE BRAKING OR COUNTER ROTATE TO REDUCE “PLAY”Section 4 - ADJUSTMENT & REPAIR 4.3.3. SHIFTER ADJUSTMENT Continued from previous pageDANGEROUS CONDITION DO NOT USE ON MOWER Section 4 - ADJUSTMENT & REPAIRNEW BLADE WEAR LIMIT. CRACKS OR NOTCHES BEGIN TO APPEAR 22º TO 28º STANDARD BLADESection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR 9. Make note of hole used in sector platesSection 4 - ADJUSTMENT & REPAIR 42” DECK SHOWN Section 4 - ADJUSTMENT & REPAIRTraction drive belt replacement VIEW FROM UNDERNEATH TRACTORSection 4 - ADJUSTMENT & REPAIR 1. Place tractor on a firm level surfaceSection 4 - ADJUSTMENT & REPAIR Section 4 - ADJUSTMENT & REPAIR REMOVE ADJUSTING KNOBS AND MOVE SEAT FORWARDREMOVE POSITIVE + CABLE LAST REMOVE NEGATIVE CABLE FIRST Section 4 - ADJUSTMENT & REPAIR 4.5.5. BATTERY TESTINGAVAILABLE ACCESSORIES Section 4 - ADJUSTMENT & REPAIRSECTION 5 - ELECTRICAL SYSTEM ELECTRICAL - B & S TWIN CYLINDER ENGINESECTION 5 - ELECTRICAL SYSTEM ELECTRICAL - B & S SINGLE CYLINDER ENGINEPROBABLE CAUSE TROUBLESHOOTING GUIDEPROBLEM CORRECTIVE ACTIONTROUBLESHOOTING GUIDE TRACTOR MAINTENANCE SCHEDULEMAINTENANCE PARTS MOWER BLADES2 YEAR LIMITED WARRANTY PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE PRIMARY MAINTENANCE SNAPPER PRODUCT REGISTRATION FORM Call the Snapper Customer Relations Center atSERVICE NOTES SERVICE NOTES SERVICE NOTES Safety Instructions & Operator’s Manual for Snapper products are built using engines that meet or exceed all applicable emissions requirements on the date manufactured. The labels on those engines contain very important emissions information and critical safety warnings. Read, Understand, and Follow all warnings and instructions in this manual, the engine manual, and on the machine, engine and attachments. If you have any questions about your Snapper product, contact your local authorized Snapper dealer or contact Snapper Customer Service at Snapper, McDonough, GA. 30253. PhoneLAWN TRACTOR HYDROSTATIC DRIVE ELECTRIC CLUTCH SERIES