Location and Function of Parts and Controls

Precautions

Front Panel

Installation

 

 

 

 

 

Avoid placing the drive in a location subject to:

 

 

 

 

 

 

– high humidity

 

 

 

 

 

 

– high temperature

 

 

 

 

 

 

– excessive dust

 

 

 

 

 

 

– mechanical vibration

 

 

 

 

 

 

– direct sunlight.

 

 

 

 

 

Only horizontal drive operation recommended, not vertical or tilted.

 

 

 

 

 

Operation

 

 

 

 

 

 

Do not move drive during operation, it may cause an error.

 

 

 

 

 

Avoid sudden temperature changes, condensation may form inside

 

 

 

 

 

 

the drive. Should ambient temperature suddenly change, wait at

Headphone

Headphone

Busy

Disc Drawer

Emergency

Eject

least 1 hour before turning off power. Operation immediately after

temperature change may cause a malfunction.

Jack

Volume

Indicator

 

Eject Hole

Button

 

Control

 

 

 

Transportation

 

 

 

 

 

 

 

Keep the original packing materials for future transport of the drive.

Rear Panel

 

 

 

 

 

 

 

 

 

 

ACTIVE TERM

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TEST

 

 

 

 

 

 

 

 

 

 

 

 

AUDIO OUT

 

 

 

 

 

 

 

 

 

ID SELECT

DC INPUT

R GND L

0 1 2

 

 

5V±5% GND 12V±10%

 

 

 

INTERFACE CONNECTOR

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Jumper block for SCSI bus

Power-in connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Audio output connector

SCSI bus interface connector

Hardware Installation

Installing the Drive Unit into the Computer

This example assumes an IBM-PC/AT* compatible computer,

a SCSI adapter card and a SCSI interface cable (50 pin flat) are at-hand.

Getting Started

Assure SCSI adapter is operational before installing CD-R/RW drive.

Prepare the necessary parts and tools not supplied:

a screwdriver

Two mounting rails if computer has mounting racks.

6 Location and Function of Parts and Controls

Precautions/Hardware Installation

7

Page 4
Image 4
Sony CD-R/RW manual Location and Function of Parts and Controls, Hardware Installation