dSWITCHER DATA connector (RJ-45)Connect to an Ethernet switch.

The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices. This network is used primarily for exchange of various types of data (key frame effects, snapshots, etc.) and still pictures of frame memory.

Caution

When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage.

eREF IN (reference signal input) connectors (BNC

type)

If you wish to synchronize this unit to an external reference signal, input a black burst signal or analog sync signal. The two connectors have a loop-through configuration. Signal input to one connector can be output from the other connector. If you will not be using the loop-through output, be sure to terminate the unused connector with the supplied 75Ω terminator.

fDME EXT IN (Digital Multi Effects External input) 1 to 4 connectors (BNC type) (BKDS-9470)

Connectors for four serial digital video signal inputs. Dedicated input for DME external video.

gDME DATA (Digital Multi Effects Data) connector (RJ-45) (BKDS-9470)

Connect to an Ethernet switch.

The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices.

Caution

When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage.

hDME CTRL (Digital Multi Effects Control)

connector (RJ-45)(BKDS-9470)Connect to an Ethernet switch.

The DVS-9000 System is connected in the same way to the Ethernet switch to form a network for exchange of signals between the devices.

This network is used primarily to control the various devices from the center control panel.

Caution

When using a LAN cable: For safety, do not connect to a connector for peripheral device wiring that might have excessive voltage.

iDME MONI OUT (Digital Multi Effects Monitor Output) 1 to 4 connectors (BNC type) (BKDS-9470)

Connectors for four serial digital video signal outputs. These connectors allow you to monitor any desired output signal with the DME signal (video, key, or with graphics).

jDME REMOTE (Digital Multi Effects Remote) connector (D-sub 9-pin, RS-422A) (BKDS-9470)

When a BKDS-9470 DME Board Set is installed, use this connector to control the unit from an external device.

kDME GPI (Digital Multi Effects General Purpose

Interface) connector (D-sub25-pin)(BKDS-9470)Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel.

lSWITCHER GPI (Switcher General Puropose Interface) connector (D-sub 25-pin)

Connect to external devices for input and output of trigger signals. Up to eight inputs and eight outputs are possible, with input and output conditions set on the center control panel.

mSWITCHER REMOTE 1 to 4 connectors (D-sub 9-pin, RS-422A)

Used to control the DVS-9000SF AUX bus from external devices, and to operate the DVS-9000SF from editing control systems such as the BVE-9100.

Specify the types of connected devices on the center control panel.

nTERMINAL connector (D-sub9-pin,RS-232C)This connetor is used for factory adjustments.

oU (signal ground) terminal Connect to the system ground.

p-AC IN (AC power input) A, B connectors (3-pin)Connect to 100 to 240 V AC power supply with the optional AC power cords.

Depending on the system’s configuration when shipped, there may be no optional HK-PSU04 Power Supply Unit installed. In that case, the AC IN B connector is not used.

Caution

For information about installing an HK-PSU04, contact your Sony service representative.

qPRIMARY INPUTS 1 to 34 connectors (BNC type) (MKS-8110SD)

These connector accept up to 34 serial digital video signal inputs. The number of connectors varies depending on the number of MKS-8110SD boards installed.

Location and Function of Parts

13