Sony DXC-D30WSP Important Notes on Operation, Settings for Special Cases, Skin Detail Correction

DXC-

Settings for Special Cases

Important Notes on Operation

D30WS/P(E)/V1

Skin Detail Correction

The DXC-D30/D30P provides an easy push-button function that designates an active skin tone area.

	ON	1
	OFF
	SET	2,3
	SKIN DTL
	1 Set the SKIN DTL switch to ON.
	The indication “SKIN AREA: ±0” appears in the
	viewfinder.
	2 Press the SKIN DTL SET button.
	This causes the area detect cursor to be shown in
	the viewfinder (for 10 seconds).
	3 Place the area detect cursor on the target, then
	press the SKIN DTL SET button.
	This designates the correction area, which is
Chapter	indicated by a zebra pattern, and the indication
	detect cursor disappears before designating the
	“SKIN AREA: ±0” appears again. If the area
5	area, press the SKIN DTL SET button again to
Adjustments	4 Press the UP/ON or DOWN/OFF button to change
	display the cursor. (Return to step 2.)
and	the SKIN AREA value (–99 to +99)so that the
Settings	zebra pattern may be displayed in the target area.

Use basic menu page 3 to set the correction level (see page 52).

You can also change color in the designated area (see the following section).

84 Chapter 5 Adjustments and Settings

Adjusting Color in the Specified Area

You can adjust the specified color using setup files. Perform the same procedure with the skin detail correction to designate the target area .

1 Turn the POWER switch on with holding down the UP/ON button.

2 Perform steps 1 and 2 in “Changing File Settings” (page 64) and display advanced menu page 11 in the most suitable file for shooting.

PAGE11(NEXTm$ PREVm4)

FILE ADJ 2 FILE: SAT:33 HUE:22

mSKIN SAT:12 SKIN HUE:15

EXIT MENU (YESm4)

3 Perform the procedure for the skin detail correction to designate the area to which you apply color adjustment.

While this procedure is being performed, the menu is not displayed.

4 When advanced menu page 11 appears, change the value of the SKIN SAT or SKIN HUE to adjust color in the area designated in step 3.

Note

Set the SKIN DTL to 1.0 in basic menu page 3 if the skin detail correction is unnecessary.

Fitting the zoom lens

It is important to fit the lens correctly, as otherwise damage may result. Be sure to refer to the section “Fitting the Lens” (See page 26).

Do not cover the unit while operating Putting a cloth, for example, over the unit can cause excessive internal heat build-up.

Operation and storage

Avoid storing or operating the unit in the following conditions.

•In excessive heat or cold (operating temperature range: –10 °C to +45 °C (14 °F to 113 °F)) Remember that in summer in warm climates the temperature inside a car with the windows closed can easily exceed 50 °C (122 °F).

•In damp or dusty locations

•Locations where the unit may be exposed to rain

•Locations subject to violent vibration

•Close to radio or TV transmitters producing strong electromagnetic fields.

Viewfinder

•Do not leave the camera with the eyepiece pointing directly at the sun.

The eyepiece lens can concentrate the sun’s rays and melt the interior of the viewfinder.

•Do not use the viewfinder close to strong magnetic fields. This can cause picture distortion.

Shipping

Use the optional LC-421 Carrying Case for optimal shipping.

If sending the camera by truck, ship, air or other transportation service, first store it in the carrying case, then pack the carrying case in the supplied carton (or an equivalent).

Care of the unit

Remove dust and dirt from the surfaces of the lenses or optical filters using a blower.

If the body of the camera is dirty, clean it with a soft, dry cloth. In extreme cases, use a cloth steeped in a little neutral detergent, then wipe dry. Do not use organic solvents such as alcohol or thinners, as these may cause discoloration or other damage to the finish of the unit.

In the event of operating problems

If you should experience problems with the unit, contact your supplier or Sony service representative.

Characteristics of CCD Sensors

The following effects may appear in the image. They are characteristic of cameras using CCDs (charge- coupled devices), and do not indicate a malfunction.

Vertical smear

When shooting a very bright object, such as a light, the highlight tends to produce vertical tails. This effect is much reduced in this camera.

Vertical tail on the image

Monitor screen

Bright object (electric light, sun, etc.)

White flecks

If the camera is operated at a high temperature, white flecks may appear in the image.

Appendix 85

Appendix

Appendix

1-49