Manuals / Brands / Home Audio / Home Theater System / Sony / Home Audio / Home Theater System

Sony 3-295-946-12(1), HT-SF1300 To cancel Auto Calibration, Performing Auto Calibration, Tip, 26), TONE, Note, SAVE, 25GB, T.S.P, ERROR, WOOFER, result, Display, Getting, process, AUTO CAL

1 72

Download 72 pages, 1.06 Mb

Performing Auto Calibration

	TV INPUT		TV ?/1	?/1
	SLEEP	DMPORT	AV ?/1	?/1	?/1
	SLEEP	DMPORT	AV ?/1

			SYSTEM STANDBY		switch
			SYSTEM STANDBY
	VIDEO1	VIDEO2	BD	DVD
					Input
	SAT	TV	SA-CD/CD	TUNER	buttons
	2CH	A.F.D.	MOVIE	MUSIC
	1	2	3	THEATRE
	1	2	3	DVD/BD
				DVD/BD
	4	5	6	MENU	AUTO CAL
	4	5	6		AUTO CAL
			AUTO CAL
	7	8	D.TUNING
	7	8	9	D.SKIP
				D.SKIP
	>10		MEMORY AMP MENU		AMP MENU
	-	0/10	ENTER		AMP MENU
	CLEAR		TOOLS/
			TOOLS/
	DISPLAY		OPTIONS	MUTING

MUTING

TV VOL

MASTER VOL

MASTER

VOL +/–

O

RETURN/EXIT MENU/HOME

Press AMP MENU, then pressAUTO CAL.You can also select “A.CAL YES” in the A. CAL menu.

The following appears on the display. A.CAL [5] t A.CAL [4] t A.CAL [3] t A.CAL [2] t A.CAL [1]

The measurement process will take approximately 30 seconds to complete. The table below shows the display when measurement starts.

Measurement for	Display
Speaker existance	TONE

Speaker gain, distance,	T.S.P.
frequency response

Subwoofer gain and distance	WOOFER

Note

You cannot measure the speaker height of the surround speakers. Set this value using “SUR POS.” parameters in the SYSTEM menu (page 35).

Tip

	When Auto Calibration starts:
	– Stand some distance from the speakers and the	Getting
	listening position to avoid measurement failure.
	This is because test signals are output from the
	speakers during measurement.
	– Avoid making noise to get a more accurate	Started
	measurement.	Started
	measurement.

To cancel Auto Calibration

The Auto Calibration function will be canceled when you do the following during the measurement process:

–Press ?/1 or MUTING.–Press input buttons on the remote or INPUT SELECTOR on the receiver.–Change the volume level.–Press AUTO CAL again.Confirming/saving the measurement results1 Confirm the measurement result.

When the measurement ends, a beep sounds and the measurement result appears on the display.

Measurement Display		Explanation
result

When the	SAVE	Proceed to step
measurement		2.
process
completes
properly

When the	ERROR	See “When
measurement	XXXX	error codes
process fails		appear” (page
		26).

continued

25GB

Contents

Page WARNING For customers in Europe Notice for the customer in the countries applying EU Directives About This Manual The HT-SF1300consists of: • Receiver • Speaker systema) – Front speaker Table of Contents Description and location of parts Front panel About the indicators on the display Rear panel RM-AAU023 FDVD/BD Press to display the menu of DVD/BD MENU AUTO CAL Press to activate the Auto Calibration function AUTO CAL O TV orange printing at the same P RETURN EXIT O – exit the menu while the 1: Installing the speakers HT-SF1300only Example of HT-SS1300front speaker HT-SS1300only 3 Hang the speakers on the screws Example of installing the speakers on the wall 13GB 2: Connecting the speakers ASpeaker cord (supplied) Note on speaker cords To connect the speakers correctly 3:Connecting the audio/ video components Component to be connected AAudio cord (not supplied) Note HDMI feature AHDMI cable (not supplied) Notes on HDMI connections AOptical digital cord (not supplied) BAudio cord (not supplied) CCoaxial digital cord (not supplied) If you connect a DVD player 4: Connecting the antennas 5:Preparing the receiver and the remote 6:Calibrating the appropriate settings automatically Before you perform Auto Calibration Example: HT-SS1300 1 Connect the supplied optimizer microphone to the AUTO CAL MIC jack 2 Set up the optimizer microphone To cancel Auto Calibration When error codes appear To rectify the error When you select “WARN CHK” When you select “PHASE” After you have finished 7:Adjusting the speaker levels and balance To turn off the test tone Selecting a component To activate the muting function To avoid damaging your speakers Listening/Watching a component Adjust to a suitable volume Blu-ray disc player Switch the input of the TV so that an image of the Watching a DVD/Blu-raydisc Refer to the operating instructions supplied with the TV and DVD player or •Check the following if you cannot listen to multi channel sound Be sure the digital audio output of the DVD player or You can select the sound field to suit the movie/music. Refer to Navigating through menus To return to the previous display To exit the menu Overview of the menus Menu Parameters Settings For details, see “Enjoying 35GB Initial setting 36GB Adjusting the level LEVEL menu parameters Adjusting the tone TONE menu parameters Settings for the surround sound SUR menu parameters Settings for the tuner TUNER menu parameters Settings for the audio AUDIO menu parameters Settings for the video VIDEO menu parameters Settings for the system SYSTEM menu parameters xSW DIST. (Subwoofer distance) Lets you set the distance from your listening position to the subwoofer xSUR POS. (Surround speaker position) •BEHD/HI •BEHD/LO Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Selecting a preprogrammed sound field 44GB Types of sound field available To turn off the surround effect for movie/music Resetting sound fields to the initial settings Listening to FM/AM radio In case of poor FM stereo reception If you cannot tune in a station Presetting radio stations Using the controls on the receiver Using the Radio Data System (RDS) Description of program types Program type Description indication 51GB Using the Control for HDMI function for “BRAVIA” Sync The Control for HDMI function does not work in the following cases: To enjoy TV multi channel surround sound broadcasting BOptical digital cord (not supplied)a) CAudio cord (not supplied)a) Preparing Control for HDMI function Watching a DVD Watching a DVD by simple operation Enjoying the TV sound from the speakers connected to the receiver (System Audio Control) You can use the System Audio Control function as follows •You can adjust the receiver’s volume when you adjust the TV volume 56GB Turning off the receiver with the TV Switching between digital and analog audio Audio input modes Enjoying the DIGITAL MEDIA PORT AVideo cord (not supplied) To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Listening/watching a connected component through DMPORT connection Using the Sleep Timer Changing button assignments Categories and the corresponding buttons To clear all remote button assignments Glossary Precautions On safety On power sources On heat buildup On placement On operation If you encounter color irregularity on a nearby TV screen If color irregularity is observed Troubleshooting Audio Video HDMI Tuner Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide If the problem persist Reference sections for clearing the receiver’s memory Specifications Speaker section HT-SF1300only •Front speaker (SS-MSP23F) •Surround speaker (SS-SRP23F) •Center speaker (SS-CNP23) Supplied speakers Front speakers (2) Center speaker (1) Surround speakers (2) Subwoofer (1) Index