Manuals / Brands / Home Audio / Home Theater System / Sony / Home Audio / Home Theater System

Sony HT-SS2000 66GB, General, Area code, Area code, Area code, HT-SF2000only, Speaker section, FM tuner section, AM tuner section, Power consumption, Power requirements

1 68

Download 68 pages, 1.23 Mb

1)Measured under the following conditions:

Area code	Power requirements
U, UC	120 V AC, 60 Hz

CEL, CEK	230 V AC, 50 Hz

2)Reference power output for front, center, surround speakers and sub woofer. Depending on the sound field settings and the source, there may be no sound output.

Inputs
Analog	Sensitivity: 1 V/50 kohms
Digital (Coaxial)	Impedance: 75 ohms
Tone
Gain levels	±10 dB, 0.5 dB step

Reproduction frequency range:

28 – 20,000 Hz

FM tuner section

Tuning range	87.5 - 108.0 MHz
Antenna	FM wire antenna
Antenna terminals	75 ohms, unbalanced

Intermediate frequency

10.7 MHz

AM tuner section

Tuning range

Models of area code U, UC With 10-kHz tuning scale:

530 – 1,710 kHz3)

With 9-kHz tuning scale:

531 – 1,710 kHz3)

Models of area code CEL, CEK With 9-kHz tuning scale:

531 – 1,602 kHz

AntennaLoop antenna

Intermediate frequency

450 kHz

3)You can change the AM tuning scale to 9 kHz or 10 kHz. After tuning in any AM station, turn off the receiver. While holding down PRESET TUNING +, press ?/1. All preset stations will be erased when you change the tuning scale. To reset the scale to 10 kHz (or 9 kHz), repeat the procedure.

General

Power requirements

Area code	Power requirements
U, UC	120 V AC, 60 Hz

CEL, CEK	230 V AC, 50/60 Hz

Power output (DIGITAL MEDIA PORT)
DC OUT:	5 V, 700 mA
Power consumption

Area code	Power consumption

U, CEL, CEK	165 W

UC	165 W (for USA)
	245 VA (for CANADA)

Power consumption (during standby mode)

0.3W (When “CONTROL” in VIDEO menu is set to “CTRL OFF”)

Dimensions (w/h/d) (Approx.)

	430 × 66.5 × 333 mm
	(17 × 2 5/8 × 13 1/4 inches)
	including projecting parts
	and controls
Mass (Approx.)	3.6 kg (7 lb 15 oz)

Speaker sectionHT-SF2000 only•Front speakers (SS-MSP2200)•Center speaker (SS-CNP2200)•Surround speakers (SS-SRP2200)

Front speakers	2 way, magnetically
	shielded
Center speaker	Full range, magnetically
	shielded
Surround speakers	Full range
Speaker units
Front speakers	65 mm (2 5/8 inches)
	cone type,
	25 mm (1 inch) Balance
	Dome Tweeter
Center speaker	65 mm (2 5/8 inches)
	cone type
Surround speakers	65 mm (2 5/8 inches)
	cone type
Enclosure type	Bass reflex
Rated Impedance	3 ohms

66GB

Contents

Page WARNING For customers in the United States –Reorient or relocate the receiving antenna –Increase the separation between the equipment and receiver –Consult the dealer or an experienced radio/TV technician for help About This Manual The HT-SF2000consists of: • Receiver • Speaker systema) – Front speakers Note for the supplied remote (RM-AAU017) The VIDEO 3 button on the remote is not available for receiver operation Table of Contents Description and location of parts Front panel About the indicators on the display MDTS NSW Rear panel RM-AAU017 D MOVIE Press to select sound fields (MOVIE) MUSIC (MUSIC) O RETURN EXIT O – exit the menu while the satellite tuner or Blu-ray disc player is displayed on 1: Installing speakers HT-SF2000only Example of HT-SS2000front speaker HT-SS2000only Example of installing the speakers on the wall 15GB 2: Connecting speakers ASpeaker cord (supplied) Note on speaker cords Note on speakers 3:Connecting the audio/ video components Component to be connected AAudio cord (not supplied) If you connect a DVD recorder AOptical digital cord (not supplied) BAudio cord (not supplied) CCoaxial digital cord (supplied) •Do not bend or tie optical digital cords 20GB HDMI feature AHDMI cable (not supplied) If you connect a Blu-raydisc player Notes on HDMI connections 4: Connecting the antennas 5:Preparing the receiver and the remote 6:Calibrating the appropriate settings automatically Before you perform Auto Calibration Example: HT-SS2000 2 Set up the optimizer microphone 26GB To cancel Auto Calibration When error codes appear To rectify the error When you select “WARN CHK” When you select “PHASE” After you have finished 7:Adjusting the speaker levels and balance To turn off the test tone Selecting a component To mute the sound To avoid damaging your speakers Listening/Watching a component Set up the DVD player Refer to “Quick Setup Guide” supplied with the receiver You can also use INPUT SELECTOR on this receiver to select “DVD” Switch the input of the TV so that an image of the DVD is displayed Watching a DVD Navigating through menus To return to the previous display To exit the menu Overview of the menus Menu Parameters Settings 35GB 36GB Initial setting 37GB Operations Amplifier Adjusting the level LEVEL menu parameters Adjusting the tone TONE menu parameters Settings for the surround sound SUR menu parameters Settings for the tuner Settings for the audio TUNER menu parameters AUDIO menu parameters Settings for the video VIDEO menu parameters Settings for the system SYSTEM menu parameters The distance between the center speaker and the listening position xSUR POS. (Surround speaker position) •BEHD/HI •BEHD/LO •SIDE/HI Enjoying Dolby Digital and DTS Surround sound Types of A.F.D. mode Selecting a preprogrammed sound field 46GB Types of sound field available About DCS (Digital Cinema Sound) About CINEMA STUDIO EX modes To turn off the surround effect for movie/music Using only the front speakers and sub woofer Listening to FM/AM radio If you cannot tune in a station In case of poor FM stereo reception Presetting radio stations Using the controls on the receiver Displaying RDS information While receiving an RDS station, press DISPLAY repeatedly Description of program types Program type Description Switching between digital and analog audio Audio input modes Enjoying the DIGITAL MEDIA PORT AVideo cord (not supplied) To detach the DIGITAL MEDIA PORT adapter from DMPORT jack Listening to digital sound from other inputs Assignable inputs for digital audio input Using the Sleep Timer Changing button assignments Categories and the corresponding buttons To clear all remote button assignments Glossary Precautions On safety On power sources On heat buildup On placement Troubleshooting Audio There is no sound from one of the front speakers •Check the setting of HDMI AUDIO in the VIDEO menu (page 41) •Check the HDMI connection •You cannot listen to the Super Audio CD by connecting HDMI The left and right sounds are unbalanced or reversed Video Tuner Remote control Error messages If you are unable to remedy the problem using the troubleshooting guide Specifications AUDIO POWER SPECIFICATIONS Power requirements FM tuner section AM tuner section General Power consumption • Sub woofer (SS-WP2200) HT-SS2000only •Front speakers (SS-MSP1200) •Center speaker (SS-CNP1200) •Surround speakers (SS-SRP1200) Index