9 HDV/DV jack (4-pin)

Use this jack to input/output the digital signals that complies with the i.LINK standard. Use when a device connected to the unit has an i.LINK jack. If you connect the unit and another device using HDV/DV jack, you can minimize deterioration of picture quality during recording, dubbing, or capturing still pictures, all by means of digital signals processing.

For details, refer to the instruction manual of the external device.

Notes

•When you connect with the i.LINK cable to a computer and the unit, check the direction of the jack. If you forcibly insert the jack, the terminal may be damaged or cause the unit to malfunction. Align v mark of the i.LINK cable with V mark on the unit and insert the i.LINK cable.

•This jack is only compatible with HDV (1080i)/ DVCAM/DV signals.

For details, see “About i.LINK” on page 98.

• If video signals have been input to HDV/DV jack and you output these video signals to the S VIDEO or VIDEO connectors, the sync and burst of the corresponding EE picture is not synchronized.

•If the unit is connected to a device equipped with a

6-pin i.LINK jack, when you intend to disconnect or reconnect the i.LINK cable, turn off the device and pull out the plug of its power cord from the AC outlet beforehand. If you connect or disconnect the i.LINK cable while the device is connected to the AC outlet, high-voltage current (8 to 40 V) is output from i.LINK jack of the device to the unit. This may cause a malfunction.

•When connecting a device that has a 6-pin i.LINK jack to the unit, connect the plug of the cable to the 6- pin i.LINK jack first.

For details on each setting when HDV/DV signals are input, see “HDV/DV SEL” (page 67).

• Video signal which is input from HDV/DV jack will be output directly to COMPONENT OUT jacks, S VIDEO jack, and VIDEO jack with the jitter of i.LINK signal. This jitter may be displayed on the connected monitor. Be aware of this jitter when you connect other recording device to for these jacks. This jitter will not appear on a recording with the unit.

•When you change the video format setting of [HDMI/ CMPNT] in [VIDEO OUT] of [IN/OUT REC] menu, the video signal output from S VIDEO OUT jack,

VIDEO OUT jack, or HDV/DV jack may be distorted.

For details on the output of HDV/DV jack, see “Notes on all video output jacks” (page 22).

q; LANC jack

Use this jack when controlling the tape transport operation of the unit using a device that has a LANC1) jack.

Notes

•LANC jack on the unit has only LANC-S functions. The unit has no LANC-M functions. A device that is set to LANC-S mode cannot be connected to the unit. Either this, the unit or the other device may not operate properly.

•When using the unit as a player, set LANC mode on the recorder to M. A VCR that does not have M/S switching function cannot be used to control the unit.

•When the device for connecting to the unit has [LANC-M] function to switch between SHUTTLE A/ B, select SHUTTLE A for HDV-formatted tape, and SHUTTLE B for the DVCAM/DV (SP)-formatted tape.

•LANC connection transmits command signals for playback, stop, pause playback, as well as the time code, tape counter, and data status of the unit.

•Jacks labeled CONTROL L have the same function as LANC jacks.

•There are some limitations when you edit an HDV- formatted tape.

Refer to the “Notes” in “Editing (Connecting with a Computer)” on page 62.

qa CONTROL S jack

Connect to a remote control unit DSRM-10 (not supplied) for controlling the unit.

You can use DSRM-20 (no longer manufactured: not supplied).

Note

When you use a CONTROL S device, set [COMMANDER] in [OTHERS] menu to [CONTROL S].

Overview 1 Chapter

(Continued)

........................................................................................................................................................................................................

1)LANC (Local Application Control bus system): Bidirectional interface used to control a consumer VCR

Chapter 1 Overview 21