Item number

Item name

 

Settings

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

501

STILL TIMER

 

Sets the time interval from the tape stop mode to the tape protection mode.

 

 

 

In order to protect the video heads and the tape, this unit enters the tape

 

 

 

protection mode automatically after a certain amount of time has elapsed since

 

 

 

the unit entered the tape stop mode (STOP mode or a still picture in jog/shuttle

 

 

 

mode).

 

 

 

0.5S ...

8M

... 30M: Set the value in the range 0.5 seconds to 30 minutes.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

651

UMID OUTPUT

 

When using the Digital Betacam or MPEG IMX format, select whether or not to

 

(J-30SDI only)

 

output the UMID data recorded on the tape from the SDI output connector and

 

 

 

the type of the UMID data if it is output.

 

 

 

OFF

 

: Do not output the UMID data.

 

 

 

BASIC: Output as the Basic UMID data (32 byte).

 

 

 

EXTENDED: Output as the Extended UMID data (64 byte).

 

 

 

Notes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Even if EXTENDED is selected, Basic UMID is output if Basic UMID is recorded

 

 

 

on the tape being played back.

 

 

 

• When menu item 901, VIDEO OUTPUT DATA is set to 8Bit, nothing of UMID is

 

 

 

output.

 

 

 

 

 

 

 

 

 

 

 

 

657

ESSENCE MARK TAPE

 

When using the Digital Betacam or MPEG IMX format, select whether or not to

 

OUTPUT

output essence marks recorded on the tape from the SDI output connector.

 

(J-30SDI only)

ON: Output essence marks recorded on the tape.

 

 

OFF

 

: Do not output essence marks recorded on the tape.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Note

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

When menu item 901, VIDEO OUTPUT DATA is set to 8Bit, nothing of essence

 

 

 

marks is output.

 

 

 

 

 

 

 

 

 

 

 

 

658

SHOT MARK ESSENCE

 

When using the Digital Betacam, MPEG IMX or Betacam SX format, select

 

MARK CONVERT

whether or not to convert shot marks recorded in the LTC track into essence

 

(J-10SDI/30SDI only)

marks and output them from the SDI output connector.

 

 

ON: Convert shot marks into essence marks and output.

 

 

OFF

 

: Do not convert shot marks into essence marks.

 

 

Depending on the type of the detected shot marks, the output essence marks are

 

 

“_RecStart”, “_ShotMark1”, or “_ShotMark2”.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Notes

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

• Of the shot marks, post marks are not converted to essence marks.

 

 

 

• Shot mark detection timing depends on playback conditions.

 

 

 

• When menu item 901, VIDEO OUTPUT DATA is set to 8 bit, nothing of essence

 

 

 

marks is output.

 

 

 

 

 

 

 

 

 

 

 

 

660

ESSENCE MARK VANC

 

When menu item 658 is set to ON, specify the line into which to insert shot marks

 

LINE

converted into essence marks.

 

(J-10SDI/30SDI only)

12H, 13H, 15H, 16H,

 

18H, 19H (525-line mode)

 

17H

 

 

09H, 10H, 12H, 13H, 14H, 15H, 16H,

 

, 18H (625-line mode)

 

 

17H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

710

INTERNAL VIDEO

 

Select the test signal to be output from the VTR’s internal test signal generator.

 

SIGNAL GENERATOR

 

OFF

: No test signal is generated. (The VTR operates normally.)

 

 

 

CB75:

75% color bar signal

 

 

 

 

 

 

 

 

 

 

 

 

713a)

VIDEO SETUP

 

Set the setup amount to be added to the composite output signal.

 

REFERENCE LEVEL

Default value:

0.0%

 

 

 

 

 

 

(When operating in 525

7.5%

 

 

 

 

 

 

mode)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

715a)

VIDEO GAIN CONTROL

 

Adjust the video output level. The only Y signal adjustment is permitted.

 

 

 

Default value:

20H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

716a)

CHROMA GAIN

 

Adjust the chroma output level.

 

CONTROL

Default value:

 

 

 

 

 

 

 

 

 

 

 

 

20H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

717a)

CHROMA PHASE

 

Adjust the chroma phase. The only composite output signal adjustment is permitted.

 

CONTROL

Default value:

 

80H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

718a)

SETUP LEVEL (525 mode)/

Adjust the setup level (black level).

 

BLACK LEVEL (625 mode)

Default value: 0H

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

a) Menu items 713 and 715 to 718 can be used only for

video processing of the analog video signal. They

cannnot be used for video processing of the digital video

 

signal (SDI/DV output).

7-11

Chapter 7 Setup Menu

Menu Setup 7 Chapter