Condition | Explanation/Solution | |
| Channels |
| |
| The desired channel cannot be | • Switch between digital and analogue mode and select the desired digital/ |
| selected | analogue channel. |
|
|
|
| Some channels are blank | • Scrambled/Subscription only channel. Subscribe to the pay TV service. |
|
| • Channel is used only for data (no picture or sound). |
|
| • Contact the broadcaster for transmission details. |
|
|
|
| Digital channels are not | • Contact a local installer to find out if digital transmissions are provided |
| displayed | in your area. |
|
| • Upgrade to a higher gain aerial. |
|
|
|
| Wireless communication |
| |
| Delay pictures | • Wireless communication takes time to establish after turning the power |
|
| on. About 20 seconds are needed to display pictures. Selecting “Quick |
|
| Start” may shorten the waiting time (page 33). |
|
|
|
| “Wireless communication in | • When the wireless communication is disturbed, it takes about 15 seconds |
| progress.” does not disappear, | to display pictures again. “Wireless communication in progress.” is |
| or “Wireless communication | displayed until pictures come back. |
| failed.” is displayed | • Check the installation situation of the monitor and media receiver (page 9). |
|
| • Check whether wireless equipment using the same radio frequency as |
|
| this unit is working near by, or something disturbing wireless |
|
| communication of this unit is close to the unit. In such cases, keep such |
|
| equipment away from the unit or turn off the power of that equipment. |
|
|
|
| Noisy or interrupted picture or | • Check the installation situation of the monitor and media receiver (page 9). |
| sound | • Pictures may be distorted if somebody walks across between the monitor |
|
| and media receiver. |
|
| • Check whether wireless equipment using the same radio frequency as |
|
| this unit is working near by, or something disturbing wireless |
|
| communication of this unit is close to the unit. In such cases, keep such |
|
| equipment away from the unit or turn off the power of that equipment. |
Distorted picture and/or sound • Keep the unit away from electrical noise sources such as cars,
|
| motorcycles, |
|
| • When installing optional equipment, leave some space between the |
|
| optional equipment and the unit. |
|
| • Check the aerial/cable connection. |
|
| • Keep the aerial/cable TV cable away from other connecting cables. |
|
|
|
| The unit turns off | • Check if the “Sleep Timer” is activated, or confirm the “Duration” |
| automatically (the unit enters | setting of “On Timer Settings” (page 33). |
| standby mode) | • If no signal is received and no operation is performed in the TV mode |
|
| for 10 minutes, the monitor automatically switches to standby mode. |
|
| |
| The unit turns on automatically • Check if the “On Timer” is activated (page 33). | |
|
|
|
| Some input sources cannot be | • Select “AV Preset” and cancel “Skip” of the input source (page 35). |
| selected |
|
|
|
|
| The remote does not function | • Replace the batteries. |
|
| • Register the remote to the unit using the / / / / buttons on the |
|
| front of the media receiver (page 46). |
|
|
|
| A channel cannot be added to | • Up to 999 channels can be stored in the Favourite list. |
| the Favourite list |
|
|
|
|
| HDMI equipment does not | • Check that your equipment is “Control for HDMI” compatible |
| appear on “HDMI Device List” equipment. | |
|
|
|
| Not all channels are tuned | • Check support web site for cable provide information: |
|
| |
|
|
|
| You cannot select “Off” in | • If any “Control for HDMI” compatible audio equipment is connected to the unit, |
| “Control for HDMI” | you cannot select “Off” in this menu. If you want to change the audio output to |
|
| the unit speakers, select “TV Speaker” in the “Speaker” menu (page 35). |
|
|
|
| The “Store Display Mode: On” | • Select “All Reset” in the “Media Receiver |
| message appears on the screen |
|
|
|
|
Information Additional